chickens

Chicken coop build, day three – finished!

/ Re-Farmer / Leave a comment

I had to make a run into town late this morning, so we didn’t even start on finishing the chicken coop assembly until much later in the afternoon. Which was fine, because it turned out to be an absolutely lovely day today.

The first thing I worked on was reinforcing the interior roost, then securing them in place.

Each corner got one of these flat braces. My original intention had been to have the horizontal roost resting on top of the vertical support, but it was difficult to get proper measurements through the tiny opening I had to work in. The roosts ended up too short by enough that I instead trimmed them about a quarter inch shorter so that they would fit in between the vertical supports, instead of on top. While the corner braces would hold them in place, these were cheap dollar store braces and I was concerned they wouldn’t hold the weight of chickens without bending or breaking. These flat braces are higher quality and will hold. The wood itself will break before those give out.

To secure the roosts, I had to use a little kitchen step ladder to be able to reach from above at the front, to set the roosts in place and line them up, while making sure they were flush against the front and back walls. There is just a bit of a height difference because of the white edging I had to account for. Both roosts had a vertical that sort of bent away from the wall, so I used one of the pieces for later in the build, jammed at an angle to brace the wonky side in place. Once they were solidly flush against the walled, I screwed them in place from the outside. Each end got three screws. Later on, I’ll use some sort of sealant on the screws to protect the wood from moisture.

The coop now has a roost on each side, on the inside.

The next stage of the build was to add the roosts that came with the kit, which were to be mounted underneath, on either side of where the ramp would be. For that, I needed an extra pair of hands and asked my daughter to come help. After I went inside and looking up online, just how they were supposed to be attached. The pictographs were really useless for that and even an image I’d shared with my daughter, showing how high off the ground they were supposed to be secured, looked like there was something else entirely going on.

She ended up basically taking over the build, and I was her assistant. Mostly because she can actually get down on the ground, and I can’t.

This time, though, we set a sheet of plastic on the ground as a drop sheet. Last time, my daughter was crawling around on the ground, she later discovered she managed to get cat poop on her pants. Ick.

Getting the exterior roosts in place was definitely a two person job. Especially for the front. With the area for the door empty, the sides sides were slightly spread out, and I had to push the entire side in and hold it in place while my daughter screwed the roosts in place.

After that, the floor between the two sides had to be installed, then the hinged ramp attached to the floor. That was all my daughter, as there was no room for me to do anything other than hand her screws.

That done, we had to attached the door to the frame by the hinges. There were a couple of plates that I’ve been using as spacers every time we had to attach a hinged door. After the door was hung, those plates were added across the insides of the frame’s corners at the opposite side, to stop the door from going past the frame when closed. Then the latch was added to the top, and the door and frame could be attached to the coop.

With the ramp on hinges, that could be lifted up and out of the way, so my daughter could go inside and screw the door frame to the coop. The ground isn’t level, so my job was to line up edges and corners and hold them in place – which required actually lifting the coop itself slightly, on one side – until my daughter got enough screws in to hold it in place, and she could do the rest without me holding things.

Once the door and frame were in place, there were a pair of cross pieces to attach between the top of the door frame and the back mesh wall of the coop. These were part of the roof supports.

The roof was the next thing to do, and it took a lot of figuring out what the pictographs were showing. We noticed some pre-drilled holes in some pieces and had to look at instructions a couple of pages later to see what they would be used for, and we could tell which direction they were supposed to face.

The roof supports were assembled in two parts before they could be set on top and secured to the coop. Then we could finally put on the plastic roof panels.

Which was more of a pain than it should have been.

First, was figuring out which side was up, as both sides were identical. They had pre-drilled holes in them that needed to line up with the supports they would be screwed into. Then there were the overlaps. After much shifting and flipping and trying again, it was the pre-drilled holes that determined which panel edge went on top of the other. It was not the way I would have expected it to, when it comes to drainage, but it was the only way one screw could secure both edges at the same time.

Once we got that figured out, and the panels were centered and lined up, we could finally start screwing them into place. For this, my daughter was using the little step ladder a lot, and we found a different problem. The ground was too soft and the legs of the ladder started to sink! I had a small piece of plywood nearby that I could put on the ground under one set of legs, which worked out very well. When it was time for my daughter to move the ladder to reach another section, I just kept moving the board.

We found other problems, though.

The screws for this part of the build are quite short. Too short for where the panels overlapped. After some digging around in the garage, I found a few that could replace some of the screws along the seams, but then we had a whole different problem along the front. For all the care we took to line up the pre-drilled holes with the supports below, the entire row of pre-drilled hold along the front were just a touch too far. The boards in that part of the roof were slightly warped. Probably from sitting in the box in the garage for over a month in the winter. There were extra longer screws in the kit and my daughter ended up using those, and not using the pre-drilled holes, to secure the roof panels. Some of the screws went in crooked and the tips got exposed, but not anywhere I chicken could hurt itself, so we weren’t too worried about it. We’ll have to go over the roof with sealant in places, anyhow.

Once the roof panels were on, the only thing left was to attach the hooks and eyes that would be used to hold open the two front doors for air circulation. For that, the hooks were first attached under the roof, and then we could use those to decide where to attach the screw eyes at the height we wanted the doors to be held open at. In spite of using a measuring tape and marking out where to attach them, we ended up doing one door at a different height than the other. The white edging in one of them had marks already on them that I mistook for the marks I’d made below! Which is fine. As long as they can be held open.

That done, the coop was officially assembled. We just had to move it.

Slight problem. The hinged ramp. With the roof in place, it couldn’t be lift up like when my daughter worked under it before. What we ended up doing was lifting is as high as we could through the open door, then quickly shutting the door before it could drop. We still had to push the ramp up through the wire mesh so the door could be closed but, once it was, the door itself held the ramp up and out of the way.

It wasn’t easy to move the hole thing. We were able to get grips on each end, because the wire mesh is on the inside of the coop, so there was enough of a lip on the frames that we could get our fingertips under there. The main problem was me and my janky elbows. I could hold the weight for only short distances before I could feel them giving out.

Still, we managed it, and set it up in front of the retaining wall, where the ground seemed to be the flattest.

It’s still not level, but at least the whole thing isn’t being twisted out of shape by uneven ground.

Where is how the finished coop looks, with all the doors closed, plus the back, which has no doors of any kind.

You can really tell in the side views, how the ground is sloping! In the front and back views, you can see the screws holding the inside roots in place.

Here are the three sides with all the doors open.

The coop was designed with the roosts below as a way of not having to deal with lots of chicken poop inside. With the added roosts sheltered inside, we’ll be adding bedding. The nesting boxes will probably get straw, but I plan to get pine shavings for under the roosts inside.

With the coop right up against the retaining wall, we can potentially secure it to the blocks so it won’t get blown over in high winds.

We will probably not be able to keep it there, though. It is facing west and the sun can shine right through the wire mesh, the sides might create too much shadow for the garden bed behind it.

One of the things I want to do if find a way to add wheels to it, so it will be easier to move around as needed. It might be easier to just make a pair of wheeled platforms that can be tucked under the ends, then removed once the coop has been moved.

This coop will work out fine for when we get our first chickens, and for the summers. It is not the strongest of structures and definitely not suitable for a Canadian winter, but the plan is to build a polytunnel in the garden this year, so that we can move the chicken coop into it for the winter. It will do until we can build a proper, sturdier, chicken coop. We’re just getting a few chickens to start; enough to supply us with eggs. Over time I want to get more, including meat hens, so we will need to expand things quite a bit. It will take time and materials we don’t really have, but at least now we can get started.

Meanwhile, we can get ready for the chicks to arrive at the end of May. We’ll need feeders and waterers (the ones my parents used are still in the old chicken coop, but I don’t know that any of them are useable, after so many decades since my parents had chickens), both for while we have the chicks in a brooding pen indoors, and for when they get moved outside.

Something else that will be coming at the end of May is our order of basket willow. I got an email from the nursery with several shipping dates available, and I requested the latest one. That will give us time to prepare where we will be planting them, beyond the outer yard, and working out how to protect them from the renter’s cows.

On a completely different note…

It is confirmed that Slick lost her litter. While working outside, I heard a commotion and it was Slick. She’s gone into heat again, and had a whole crowd of dudes wanting their turn with her. She was not happy about it, either. I sent a quick message to the rescue and they want me to trap her as soon as possible. I don’t think we’d be able to trap her specifically, though. However, she has been super friendly when we do the morning cat feeding, and we might be able to get her into the big carrier. Tomorrow morning, my daughter is going to come out with me to try and get her. If we can manage it, she’ll go to the rescue for however long it takes for them to get her spayed, then she will come back here.

If we can get her contained!

Here’s hoping!!!

The Re-Farmer

Costco stock up trip: this is what $800 looks like

/ Re-Farmer / 6 Comments

$799.40 to be exact. 60¢ under budget. 😄

First, though, an update on the truck.

The first thing I noticed when I started it this morning was that the clock’s time was wrong. I’d reset it yesterday. Which means, we lost power to the console during the night, and it came back.

As my daughter and I were starting the drive, we were talking about what’s been going on with the truck, and how weird it was for the tire warning message and light to not be there anymore.

Then, just shy of the highway, less than 2 miles from home, both the light and the message came on.

*sigh*

We had left earlier than usual to meet someone from the rescue to get our top loading cat carrier back, but also to stop in the town my mother is in (again). We picked up a couple of energy drinks and sandwiches for breakfast, then went to the feed store to pick up the lysine. They were still closed, though, so we kept on going to where we were arranged to meet up. We had plenty of time to eat our sandwiches and just sit and talk.

Once we had the carrier again (they even cleaned it!), it was off to the city and Costco.

I could not believe how full the parking lot was, for a Wednesday morning! It was really busy in the store, but the bigger surprise was as we left. There was a huge line to the customer service desk, running all the way to the main doors outside. I don’t usually see that kind of line except after Christmas.

Still, we got what we needed to get here; anything left on our list will be done on our next Walmart run.

There is is. $760.67, before taxes. After the cart was re-loaded, we had to stop and my daughter reorganized things. Because of the crowds and line to the Customer Service desk, we had to do it outside. As our stuff was being scanned, a guy showed up to load the cart and he basically just threw everything onto the flat cart with no attempt to be secure or even logical about it. My daughter and I are both very keen on packing and stacking things well, so it was hard to watch! 😄

This picture was taken before my daughter was done reorganizing so no, those eggs did not stay balanced on top of the pierogi at the end of the cart!! 😄

This is what we got today.

We did get cat supplies, though with the generous donation, we should only need maybe one more 40 pound bag of kibble before the end of the month for the outside cats. We didn’t need any for the inside cats, so the two 9kg and two 11.6kg bags are all for the outside cats. I think the price on the 11.6 kg bags went up. Either that, or they were on sale that last time I remember getting them.

We also got a case of canned cat food and a case of XL puppy pads. We now have enough canned cat foot that we won’t need to pick up more for the rest of the month. Usually, I get a couple smaller cases at Walmart to have enough for the month.

For non-food items, we got our toilet paper, AAA batteries, and some more Head and Shoulders that gets used as an anti-fungal body wash.

For beverages, we got a case of Coke Zero and a case of Monster. The Monster variety pack had replaced one of the flavours from before, and it’s to one I like but haven’t been seeing in stores much at all lately, so I’m happy. It was also on sale, so that was bonus. There is also a 3 pack of oat milk for the girls.

In dairy, we got a 4 pack of cream cheese, a carton of whipping cream, a block of Old Cheddar cheese, plus 5 pounds of butter.

For meat and other protein, there is a double flat of 60 eggs, a panini pack of sandwich meats, some pickerel fillets for the girls, two big packs of drumsticks that were $5 off at checkout, a pork blade, a pork loin, and a variety pack of dry sausages that was on sale. I also got two garlic coils, as the price was almost half what they are, locally. Oh, and some canned chicken. The price on that seems to be staying under $20 for six cans of late.

There is also a bag of carrots – organic, but they were on sale, and we didn’t see any non-organic ones anywhere, a 20 pound bag of Russet potatoes, frozen perogies, a case of ramen noodles, a bag of basmati rice, a case of tomato soup, large jars of mayo, peanut butter, and pickles. There is a two pack of butter chicken sauce, a shaker of powdered garlic (which, oddly, had more product for a lower price than the granulated garlic I usually get), and a large bag of granulated sugar.

For bread products, I got a 2 pack of rye bread and we got two packs of tortilla wraps. Finally, as a treat, my daughter selected from toffee and chocolate chip cookies.

Note that we did NOT get any beef. We haven’t been able to afford beef at Costco for a while, now. Lately, I’ve been picking up the odd package on sale, locally. The last couple of times I was in town because of the truck, I got some stew meat and some ground beef with sale prices much better than Costco these days.

Once the truck was loaded up, we filled the gas tank. Costco gas was at $1.239/L instead of $1.359/L everywhere else! It cost $51.69 to fill the tank.

On the way home, we stopped at the feed store and picked up the lysine. It came in adorable little 1kg buckets from a different brand this time. The price went up, so the two of them cost $67.20 after taxes. The containers I got before had been $20 each. Still better than buying it elsewhere.

When I saw the buckets, I commented on them, and that I would probably be keeping them to reuse. The woman behind the counter completely agreed with me – you can’t have too many buckets!

She also asked me if I was still wanting to get chicks.

I said yes, absolutely.

She asked if I was after a specific breed or anything like that, and I said I just want laying hens. She named several breeds, and I was fine with any of them. Then she asked about the date I’d want them, snowing the hatchery’s schedule on their white board.

There was no way we’d be ready for them in April! I told her, we need to be able to assemble the chicken coop first, which means, no snow on the ground. (Yes, I know; they’ll be in a brooder for weeks, first, but I still want to have the coop assembled and ready, before we get them.) So she put me down for the latest date they had, which is May 27. She has two other people who are interested in getting a smaller number of chicks than the 24 chick minimum the hatchery sells them for. I told her that, with our coop, we can have a maximum of 10 chickens, so we can go under, but not more than 10. So she will talk to the other two people and see what can be worked out to split an order of chicks between us, as well as splitting the shipping costs. With three people, we’ll be paying $15 each for shipping instead of $45.

Hopefully, we’ll be able to work something out with the other two people and get it all arranged and ordered. I’m flexible on the delivery date, too, as long as it’s not in April! She said, all three of us have said we are flexible on things, so this should work out quite well.

My daughter had been waiting in the truck all this time, so once we were back on the road, I updated her about the chicks discussion.

I think she is actually starting to look forward to having chickens! My daughters had been very reticent about it. Especially her sister. They have online friends who keep chickens, and my older daughter had commented about chickens getting sick, and we wouldn’t be able to take them to a vet.

Well, no, but we would be getting what we need to treat them ourselves! The feed stores carry medications and supplements for chickens, as well as feed. There’s lots of info out there on treating chickens.

Then we got to talking about where to set up the coop.

Ideally, I’d like to have it where we can easily see it, which would be in the south yards. Most of it isn’t level, and some significant portions of it floods in the spring, so that likely won’t work. I mentioned I was thinking of having it sheltered in the maple grove, or even where we currently have a pile of maple logs from the trees cleared away from the roof. The ground under that log pile is quite level, and I can see it out my bedroom window. Inside the maple grove would be more sheltered and there are fairly level spots there.

My daughter suggested we set it up against the retaining wall blocks at the end of the old kitchen garden. I had considered that area, but it would have to be at the northernmost end, as the south end is next to an area that gets deeply flooded in the spring. It’s not as sheltered from the wind, but it does get more light than if it were in the maple grove.

The other thing to consider is being able to secure the coop from being blown over in high winds. We’ve previously talked about getting panels that we can set around the mesh sides on windy days. The roosts are under the floors of the nesting boxes, rather than inside. There are three nesting boxes, with access from outside, at each end of the coop. When we assemble it, I want to find a way to attach a couple of roosts in the space in front of the nesting boxes, so they can roost for the night indoors, and not be exposed to the wind.

Ultimately, though, where we set up the coop will be temporary. I still plan to have some sort of polytunnel or greenhouse of some sort over garden beds in the main garden area. The coop and chickens would spend the winter inside that. So while we will need to secure it to make sure it doesn’t get blown over in high winds, we still need to keep it mobile.

I quite enjoyed talking it out with my daughter!

Anyhow.

Once at home, I had to drive up to the house to unload. I had some concerns on whether or not I’d cleared away enough snow before my body gave out. Especially the area I pull into behind the garage, so I can back up to the house. Sure enough, while in 2 wheel drive, I got stuck. I switched to 4 wheel drive and was able to back up. It was hard to tell, but I think that shuddering had started up again, while I was reversing in 4 wheel drive. The distance was so short, though, I really couldn’t say for sure. I just made sure to switch back to 2 wheel drive as soon as I was stopped, so I wouldn’t forget later.

Then it was the assembly line to unload the truck into the house. Last of all, my daughter and I took the kibble bags into the old kitchen. The whole time, we were constantly needing to make sure Sir Robin didn’t get into the house! He so wants to be inside!

Once the last of it was done, I left my older daughter to put things away while I grabbed some hot water and did the outside cats early. My younger daughter took over doing the kibble while I topped up the water bowls. Once all the cats were distracted, I was able to drive the truck out of the yard. I only had to scoot two of them away, first!

So there was have it. Finally. Our Costco stock up trip is done!

We will still need to do the Walmart and Canadian Tire trips, but that’s not as urgent, and there isn’t a lot we need to get there.

What I do need to do is visit my mother! I am planning to do that tomorrow afternoon, so I’ll be calling her tonight to let her know. My sister should have been able to visit her today. Maybe. During the drive home, we hit some pretty crazy blowing snow conditions, but it did clear up before we got home. As I write this, we are at our predicted high of -13C/7F, but the wind chill is -28C/-18F

Oh, my! Not only are we warming up over the next few days but, as I write this, we’ve got a high of 6C/43F forecasted for Sunday! 6C!!!! Wouldn’t THAT be nice!!

So, tomorrow (Thursday), I visit my mother. The day after, I have my doctor’s appointment. Saturday, I want to make a trip to the dump. Just a regular garbage and recycling run, though; my mother’s old mattress and box spring, and the broken office chairs, will have to wait for another day. Monday, my daughter has a doctor’s appointment. After that we don’t have anything scheduled until my dentist appointment near the end of the month, but March is also a birthday month for my older daughter. For her special birthday dinner, she usually chooses Pizza Hut pizzas. So at least one more trip there (no one delivers where we live. 😄)

Well, our mechanic has said, we need to drive the truck often. Mechanically, it’s running fine, with the possible exception of the shuddering in 4 wheel drive that comes and goes. I can just keep it in 2 wheel drive until absolutely necessary. They’ve checked and re-checked, and they can’t find anything wrong that could be causing it. The weird electrical thing has only affected the console and radio. The dashboard display has not been affected.

It’s still hell on my nerves, though.

The main thing is, we have transportation again, AND we finally got our first stock up shopping trip done – a week later than usual!

All is good.

I just have to keep telling myself that!

The Re-Farmer

Our 2026 Garden: new seed starting set up

/ Re-Farmer / Leave a comment

Well, I got one package at the mail.

I’m glad I didn’t decide to just wait until the post office reopened in the afternoon. I forgot today is Wednesday. The store the post office is in closes at noon, every Wednesday, for inventory.

I was expecting the chicken coop to come in several large boxes, but there was only one small box. Only one package slip in my mail box. No coop. There was no “attempted delivery” this morning at all.

Hmmm.

Something to look up when I got home, and after I checked out my new stuff.

This is what I got.

Two new heat mats, two 4 light clamp lamps and one 5 light tripod pedestal lamp, with full spectrum lighting.

This gave me a chance to do a few things all at once.

Right now, my work table is covered with a gain self-healing cutting mat my darling husband got for me some time ago. Unfortunately, the heat mats make it warp. So I cut some pieces of half inch rigid insulation to size, to go under the heat mats.

The heat mat with the germinated plants in it got a piece of carboard between the mat and the tray as a buffer. Normally, I would stop using a heat mat as soon as the seeds germinated, but it’s so chilly in the basement, that’s not really an option. Especially since I will no longer use a light fixture that puts off a small amount of heat. The buffer will keep the seed starting mix warm, but not too warm.

The large celled tray now has a new heat mat under it. I’ve filled the last empty cells with seeds that were set to pre-germinate, even though they were not germinated yet. Then, just in case, I added a couple of fresh seeds into each cell. I did actually see a single Caspar eggplant starting to break through the surface, but nothing in any of the other cells. It’s entirely possible the seed starting mix, not being on a heat mate, but getting some heat from above, was too cold.

I also added new luffa seeds to the three Red Solo cups where nothing has shown yet, including the one where I couldn’t find the pre-germinated seed at all.

The new lights have a controller with several settings. There are five brightness settings – I put them at the highest. They can also adjust from red, blue or white light, or all three. I have it on all three. It can also be set to shut itself off after 6, 12 or 16 hours. I set it to 12 hours. Each lamp also came with an adapter, so they can be plugged in as usual, or can have USB. I have a power bar hanging above that has a couple of USB slots in it, so I decided to use that.

The only problem is that these are clamp lamps, and cannot stand on their own. Which means I had to move the tray set up to the front of the table for the lights to reach. Only at the front of the able is the surface narrow enough for the clamps. This worktable has a sheet of plywood on top of a narrower table top. The ends are too thick for the clamps.

With a full tray of cells, plus a second tray that’s only partially full, I set things up so that the full tray has five lights over it, and the other has only three.

I’ve still left the shop light above on. That light is manual, so I’ll need to shut it off and on, but that’s okay.

I am looking to pick up more seed starting mix when we are out and about tomorrow then, either on Friday or the weekend, I’ll start more seeds. Specifically, I’ll be starting herbs.

The tall light fixture will be set up in the living room. The onions in their seed snail rolls are getting plenty of light, with the shop light lowered to their level, but the other plants around them could really use better light! That room gets the morning light, and that’s it. It’s pretty dim, the rest of the day. We don’t have a lot of plants anymore, after repotting and donating most of them to the large animal rescue that took Poirot’s orphan kittens last summer. That, at least, will make it easier to give them proper lighting with this new lamp.

The lights themselves were very reasonably priced. The smaller lamps were under $25 each. It was actually cheaper for me to buy as a quantity of two separately, than to buy a single 2pk, which is weird. The larger lamp was under $40, regular price, and I got that one on a 10% off sale.

That done, I went looking to see what happened with that coop delivery.

Now, when placing the order, I was really surprised that would be delivered by Canada Post. When checking the tracking for the two packages I was expecting, they were the same. They even went through the same delivery depots at the same time, though the lights were ordered several days before the coop was.

Any time an order arrived, the trackers say “delivery attempted”. Of course, no delivery is attempted at all. The packages are just left at the post office for us to pick up with the regular mail.

Today, however, the coop’s tracking now said “undeliverable” and “location unknown”.

It also said, Fed Ex.

*sigh*

If I’d known is was going to be Fed Ex, I would have used our physical address. They have actually found us and delivered to us before.

I tried using the “contact shipper” link on Amazon, which took me to a page with a list of delivery companies.

None of them, Fed Ex.

So I went to their website and eventually found a customer service number to call.

After going through the robot sentinel, I actually got to talk to a real human being! Not only that, but he was awesome!

I gave him our physical address, including both the name and the numerical designation for our road. He put me on hold to work on it, then had to come back to ask more confirming questions. I told him, our address doesn’t exist on Google maps. He did, however, find a road with the numerical designation – but under the name of our municipality, not our little hamlet. So I had to explain that that section of road ends at a crossroad, then restarts a short distance off before continuing for several miles. It’s those several miles that are the empty void in the map, and we are in the void. In the end, he was able to take directions and instructions on how to get to us, and how to find our driveway – with the warning that if they miss our driveway, they’re not going to find the next one to turn around in for another mile. I also told him about the sign we have, with our physical address on it, and arrows pointing the way, at the turn off. Because we’ve had this problem before!

We had a lot of laughs while working this out.

I asked if they would be delivering tomorrow, and he said it was very likely. So I told him, I’ll be out for most of the day, though there will be someone home. I let him know we would leave the gate open, and the garage, and the package can be delivered into the garage. I don’t know how many boxes this is going to go into, but it’s warm enough that I don’t mind not parking the truck all the way into the garage, so make room for the boxes.

We will need to figure out where to assemble the coop. It needs to be relatively close to the house, on level ground, and in an area that doesn’t get flooded out in spring melt. Wherever we decide to set it up, we’ll probably have to level the ground. We really don’t have level ground anywhere!

On the plus side, this is a relatively small coop. It would be easy to move, if we ever need to. It could even get set up in the main garden area, where we can let the chickens help prepare the soil for us, where more raised beds are going to be built. The coops is just under 4′ wide, and just over 6′ long. The raised beds we will be building in the main garden area will all be 4′ x 18′. It could be set up where a new bed is planned and either moved 6′ every few weeks, or an extended run could be built to cover the 18′. I’ve got enough chicken wire for that. I’d just need to find the materials to frame it out. The coop design I got has the eggs boxes and roosts above and an open run below, with wire mesh walls. It would be easy to make a door to access an extended run. The only hitch is that access to the nesting boxes are at the ends, so a run on the end would make it harder to reach.

Hmmm… Things to think about.

We’ll have snow on the ground for quite a while yet, though, so there’s plenty of time to figure it out.

The Re-Farmer

Morning kitties, updates, and yes, I got more seeds

/ Re-Farmer / Leave a comment

First, the cuteness!

The outside cats are certainly running around a lot more, now that things are warming up! It’s going to get quiet pleasant for the rest of February, according to the long range forecast, though the local weather group I follow is monitoring a weather system that might push a Colorado Low into our area.

I never got a call from the hospital yesterday, so I called them before going to bed. I’m glad I did, because my mother called me this morning!

She is still in the hospital, all packed and ready for her transfer. She told me she asked the staff about when she was leaving, and that they told her they didn’t know how she would be transported. Which is strange, since they told me from the start that they are arranging her transport.

The doctor at the hospital was never able to connect with the doctor and the temporary care unit, and that’s why she didn’t get transported yesterday. I explained that to her, and assured her that the hospital would be arranging the transportation. Likely with a HandiVan, rather than an ambulance. My mother didn’t even know where she was going, other than it would be in the smaller, nearer city. I told her, she would be in the old hospital, now converted to temporary long term care, but that we still didn’t know where in the building she would be. She was satisfied with that. She sounded like she was really looking forward to the transfer!

Late this morning, I headed out to the feed store in the town my mother no longer has an apartment in. 😄 We’re heading into the middle of February already (how did that happen so quickly???), and we still had kibble, so I only got three 40 pound bags. I also ordered some lysine, which should be in on Monday. Or Tuesday. Monday is a statutory holiday (it has different names in different provinces) and I think they will be closed.

Since I ordered that chicken coop – which got shipped yesterday already! – I stopped to ask some questions about chickens. The two people that were there at the time got quite enthused in answering them! I’ll need to set up a brooder (I already have the heat lamp, currently being used in the sun room for the cats). They gave me a booklet from the hatchery they get their chicks from that has all the information needed. I know we still have feeders and whatnot in the old log building my parents used as a chicken coop when I was a kid, but I’m not about to go digging those out. They’ve been there for probably 30 or more years by now. I honestly can’t remember when my parents stopped keeping chickens.

I asked them which breed they would recommend for someone just starting out and looking for layers. They both very enthusiastically recommended Browns. They were really impressed with the number and size of the eggs this breed lays, plus they are known to be quiet, friendly and clean.

The chicken coop that’s on its way is big enough for only 10 chickens, which is a bit of a problem. The hatchery’s minimum order is 24 chicks. There is, however, someone else that’s looking for only a few chicks, so they took my name down alongside theirs. If they can find one more person, they can split a shipment, and the shipping costs, after the chicks arrive. It costs a bit more for sexed chicks, but with only 10, I don’t want to have any roosters in there. By the time everything is added together, it should cost me about $75 for 10 chicks. Meanwhile, I can slowly start picking up the other supplies I will need, like feeders and waterers. I can get pine shavings locally.

Over time, as we build bigger coops, we’ll look at getting meat birds, too. If we’re looking to fill the freezer for a year, we’d be looking at at least 100 meat hens, so that would require a much bigger coop! Or multiple smaller ones. It’s a shame the building my parents used can’t be used. We might still be able to fix it up at some point – it’s still in good enough shape for that, at least – but that is very much a long term project.

Once I was done there, I topped up the gas tank ($1.279/L *sigh*), then went to the grocery store. I was mostly looking to get more rye bread, but found a few more things, of course – including some tri-tip beef that was on sale. Beef has become something where local prices tend to be better than Costco prices. At least when the sales are on. Still high, but at least affordable enough to grab the odd package now and then.

I also got sucked in, as soon as I walked in the door.

There was a seed display. The first I’ve seen this year!

Of course, I had to look, and yes, I did get seeds.

The first are some double marigolds. These are something I want to scatter plant all over the various garden beds, wherever there is space. They can be started indoors 4-6 weeks before last frost, so around the middle of April or beginning of May. Marigolds are easy to collect seed from, so I should hopefully be able to collect some for next year.

I also got some yellow zucchini, because I just can’t have too many summer squash! These can be started 3-4 weeks before last frost, so in the beginning of May.

Both can actually be direct sown, too, so I might try a bit of both. It depends on how much room I find myself with.

I seriously had to resist buying more!

So we are set for the next while. I don’t need to head out anywhere again until it’s time to take the truck in to get the differential leak fixed – a 2 hour job. I had intended to visit my mother while the work was being done, but she shouldn’t be there anymore. Depending on when they can start working on the truck, once it’s done, I will likely to head to the city my mother will be in, to hit a Walmart and a Canadian Tire, both of which are quite close to the old hospital building she is being transferred to.

I’m actually surprised I haven’t gotten a call from the hospital yet. That means she hasn’t been transferred yet. I would have hoped the doctors had connected by now!

Ah, well. We shall see. The main thing is, she is safe and care for, either way.

Now… time to start pouring through that hatchery booklet I picked up today!

The Re-Farmer

Addendum: Oh! I just hit publish when a message from my brother came in. The hospital just called him. My mother is transferred, safe and sound!