Yesterday afternoon, I got some progress done in the maple grove.  I don’t expect to do more later today, as it’s supposed to get quite hot again.  We shall see.

At this point, I’m just slowly working my way Westward from the garden path I recently cleared out.  I had already gone through here and taken out the fallen branches that I could find.  Well.  At least the bigger ones.  I’m always finding more, hidden under the tall grass!

Here are some before and after pictures. :-)  (click on them for larger images)

This is the area directly North of the trees I’d been working on a little while ago.  Quite a bit of dead brushes that I couldn’t tell what they were.  Some seemed to have either very long thorns, or very pointy twigs!  Those pretty much pulled out of the ground, they’ve been dead for so long.

Just past the elm tree on the right of the photo was this…

I really liked it when I found it; that moss covered stump of an old maple looks to nice.

Most of what was around it was dead or dying, with little bitty new growth coming up and making it look more alive than it really was!  I did keep the two strongest ones, which you can see in the after photo above.

Lots to clean up, here!

I would have loved to keep the two maples in front (you can see their remains in the after photo), but they were right under the power lines.  Maples can get so huge, there was just no way it was worth leaving them.  Better to take them down when they’re small then when they’re big.

I had gone in with the weed trimmer, first, just enough to clear away the grass so I could see any hidden branches.  Even though I’d cleared a lot out already, there was quite a lot left to take out, even before I could start cutting and pruning.

The spruce tree with the rock at the base is dead, and is the one we will be getting the arborists to take down when they clear the power lines.  It isn’t at the line, but is tall enough that if it falls, it could land right on it.

You can’t see it in the after pictures, but I was able to clear a smaller dead spruce behind the big one.

I didn’t think to take a before picture that included the power pole.  I hadn’t expected to clear anything that far.

The maple tree in the foreground is going to have to come down.  I hate to do it, as it’s a nice, healthy tree, but it’s also right under the power lines.

I also cleared some small elm and maple from by the power pole for the same reason.  I cut away the bottom branches of the spruce near the pole, but am considering if it’s worth the risk of keeping.  It’s not directly under the power lines, but when it reaches its full height, it would be a falling risk.  I think I’ll wait until we are ready to get the arborist in and ask them.

Some of the dead spruces could just be torn out of the ground, like this one!

I cut back the lower dead branches on a couple of little spruces, but some of them have only a few living branches barely above my head.  As I work my way down, I’m going to have to pick and choose which to keep and which to take down.  Once there’s more space between them, while also clearing away more from the trees near them, I’m hoping the survivors will have enough sun and space to fill out and grow stronger.

Oh, and those vines!!  They are everywhere!

Unfortunately, I may have done something to my new little chain saw!  After a while, it start to “scream” and get easily jammed.  I took it into the sun room (where I keep the packaging, and the tools that came with it), opened up the side and started cleaning out the blade oil soaked sawdust that was jammed around the blade.

Then the blade and chain fell off.  I was hoping to avoid that.

No worries.  I’ll just pop it back on, right?

Suddenly, I couldn’t remember if the blade had landed upside down, or right side up!  I took out the instruction booklet and read it over.  According to the diagram, the logo should be facing me as I put it on; except the logo is already warn off.  The print on the other side is still very visible, but that isn’t anywhere on the diagram.

If I look at the image elsewhere, however, the logo is on the other side of the chainsaw.

Now, I know I put it on facing the right way.  My head knows that.  But I can’t help but keep double checking.  Finally, I was done, brought it back to where I was working, tried to cut my first branch and…

It’s still screaming, and jams easily.

So I just stopped it and set it aside.  Then went back to using a hand saw.

Not going to take any chances!

Some of what is in here is going to have to wait for a full size chain saw, anyhow.

It’s going to look so good in here when I’m done!

The Re-Farmer