plumbing

A productive day, more or less

/ Re-Farmer / Leave a comment

Today, I needed to drive my mother to her doctor’s appointment, but didn’t have to leave until morning.

That gave me a chance to check on our emergency diverter set up that my brother made outside the house, ensuring that things were still sitting where they needed to.

Aside from making sure the PVC pipe my brother found was snug against the house, this is the important part.

The orange tarp partially buried in snow is the end of the insulated tarp covering the septic tank that we did not have to move. It was pulled away from the house, instead. This end gets frozen harder to the ground.

The two lengths of pipe need to be kept straight and slow downwards. At the bottom left corner of the above photo, you can just see the section of chimney flu that is supporting it closer to the house. We used basically what we could find in the dark. They will do the job, as long as things stay where they are supposed to. The shoveled area in the snow will basically become a skating rink.

In the distance, you can see the large flexible hose that was meant to be used. The problem is, it doesn’t straighten out entirely. Ever snake-like turn is an area that water could potentially slow down and freeze. The pipe is about 6″ in diameter, but even that can eventually fill and freeze solid. So it looks like we won’t be able to use it.

But I’m getting ahead of myself.

Using my brother’s car (and making sure to give the engine time to warm up, first!), I headed out early enough to hit the post office.

Alas, the mail that I’m expecting that didn’t come in due to the postal strike, still has not come in. Nor has anything else. Not even junk mail. The strikers may have been ordered to return to work (as a Crown corporation, the Federal government has the authority to do that), but apparently, that doesn’t mean they are going to actually do their work.

Oh, something I learned about this strike. It turns out that Canada Post has two unions. One is for the regular postal workers we see delivering our mail and in the physical buildings, like in our little hamlet. The other is for the ones that work in the distribution centres and such. Those are the ones that went on strike. So, while regular postal workers still showed up for work, they couldn’t do anything, because the distribution centres were shut down. It was a rotating strike, so every week, a different distribution centre would be active again, allowing for some mail to trickle through. Of course, if it was going from one distribution centre to the next, that really didn’t make much difference.

But I digress.

From there, it was off to my mother’s town and, since I was so early, I swung by the hardware store. After talking to one of the staff, I picked up some reflective insulation. They sell this stuff in sizes large enough to wrap around hot water tanks, to narrow strips that would be wrapped around pipes. Which is exactly what I wanted. I also got a small roll of aluminum tape. I plan to wrap the outflow pipe where it butts up against the house, as that is the area most at risk of freezing. Then I plan to add some between the pipes and the supports. Where the log is, isn’t much of a concern, but the ceramic chimney flu and the brick can both chill the pipe and potentially cause an ice build up on the inside. Just a bit of insulation would prevent that.

From there, I made a stop at the gas station. I didn’t need gas yet, but I knew my mother would be getting her Meals on Wheels today. Though I had a large and late breakfast before I left, she had told me she didn’t like to be eating by herself, with someone watching her. So I picked up some of the potato wedges she likes so much, so that I could snack while she was eating, and she could have the rest with her supper, later on.

When I got to her place, though, she had just finished eating her main meal. So we had some tea while she ate her desert. 😊 We were able to have a bit of a visit before we had to leave, and I updated her a bit on what was going on, and that my brother had lent us their car rather than my SIL driving all the way out to drive both of us around, and that he’d installed the diverter. I’m not sure, but I think she was still living at the farm the last time (and first time) it was used.

We left early to go to her doctor’s appointment, and I’m glad we did. I ended up having to go back to her apartment to get her little folding foot stool. Even though the car is so much lower than the truck, she still needed the stool to be able to get in! That is a definite drop in mobility.

Once at the clinic, we had a long wait, as everyone was being called in late. Once in the examination room, we still had a bit of a wait. When the doctor finally came in, she started off asking if we could move to another room, but then she saw my mother and told us to stay put, she would go get her laptop. It turns out the clinic was having network problems with all the examination room computers, and that was why everything was behind.

So we tried to keep it short. The main thing was to get my mother rescheduled for the MRI we didn’t get to, due to dangerous road conditions. I confirmed that my mother’s file was up to date about her macular degeneration and treatment. The doctor has nothing to do with this, as my mother is being treated at the eye clinic in the city, but as the primary doctor, she is supposed to have all this information sent to her. Then we talked about my mother’s breathing issues. One of her neighbours has asthma and uses a puffer (inhaler), so my mother decided she should have one, too. So could she be tested for asthma?

The doctor just prescribed her a puffer. She explained that she could recommend her for testing, but that is done in the city, and my mother would be on a waiting list for probably a year. Using a puffer won’t hurt her. I don’t think my mother as asthma, but even if there’s just a placebo effect, it would be worth it.

After giving my mother a basic physical exam, the doctor adjusted one of her dosages, and that was it. We knew the doctor was behind because of the computer issues, so we didn’t talk about much else. Which is good, because my mother usually wastes time by asking personal questions, or bringing up issues that she has… opinions on, shall we say.

My mother wasn’t due for any bloodwork, but the doctor did want to see her again in 3 months, so I made that appointment before we headed out.

Since the doctor faxed the new and updated prescriptions directly to the pharmacy in my mother’s town, that was our first stop. I went in while my mother stayed in the car, as it was just too much for her to go in and out. My mother was due to have her bubble packs delivered on Friday, and has started her last week’s current pack, so when I got there, her new packs were already there and ready to go. So that got pulled and adjusted for the new dosage. Instead of delivering on Friday, they will deliver tomorrow. As for the last pack my mother just started, the pharmacist said for her to set it aside and use the new once when they arrive, and the current pack can be brought back and adjusted.

As for the inhaler, it would take an hour before it would be ready, so that will be delivered tomorrow, too. Having been given an inhaler to see if it would help with my own respiratory issues (which we’ve never found the cause of, and I’ve basically given up trying to find one), I was able to explain to my mother how they work and how to use one, etc. She’ll need reminding, of course, but I hope the staff that delivers her meds tomorrow will be able to explain it again.

That done, there was just a brief stop at the grocery store for me to run in and pick up a couple of things for my mother before I took her home. I didn’t stay too much longer after that. I’m glad the days are longer, and I did manage to get home while it was still light out.

In between all this, I was able to send the OBDII scan results on the truck to the garage and he was able to respond. It’s basically the oil pressure sensor again. The one that was recently replaced, and also recently cleaned out because it was triggering the alarm and “shut off engine now” warnings, because it thought the truck was out of oil. This time, it has so far just turned on the check engine light again (though I did clear the codes, so that should be off now), and it why the oil pressure gauge isn’t moving. He told me, even if he replaced the sensor again, it’ll keep happening, because of the weather we’ve been having. There’s really nothing he can do about it. I suppose I could pay him to take it apart and clean it again, but that’s about it.

So really, what I need to be doing is getting the engine warmed up and staying warm long enough to evaporate any moisture in the system and triggering the sensor. It’ll resolve itself as things warm up again, as there won’t be that build up of moisture anymore.

I don’t need to go anywhere tomorrow, and it’s supposed to be a bit warmer, so I’ll run the engine while I’m outside.

Which leads me to my phone call with my brother this evening.

I’d sent the pictures he took to the company that installed the ejector, and the response was the same. The pump isn’t pushing out the water fast enough to create the pressure needed. This frustrated my brother to know end, because he knows the pump is pushing fine. As for how long it takes to drain the tank, he told me that 5 minutes is about right, because our tank is about twice the size of most other tanks. It’s huge. I was so young when it was installed, I was probably not allowed to go anywhere near it at the time.

Plus, that ice wall on the sheet of metal roof the ejector expels the water onto shows just how far and how strong the flow of water is.

Or was.

I know I’ve described the ejector system before, but my brother sent me some info with a diagram. The image was a pdf and terrible pixelated, but I think I got a decent screen cap of it.

I don’t know if ours is from this company, but it’s the exact same design.

With our new ejector, it’s about 2′ above ground, so about 8′ is below ground. I think the original was more like 12′ based on how much more was above ground than the new one. The venturi pipe – the discharge pipe, in the diagram – should never stay full once the pump shuts off. Once installed, the venturi pipe can be (carefully!) removed and replaced, which is what we were supposed to do after using enough hot water to thaw the ice and free it.

One of the things my brother brought up again was electric heat tape. There are all kinds of heat tape, and my husband had sent me a link for one that he’d found on Amazon. As my brother voiced concerns that, if we did try to use heat tape to thaw the above ground portion of the 4″ stand pipe, it might melt the plastic, I sent him the link. It is safe for both metal and plastic pipes, and self regulating. It’s also available in a huge range of lengths. He estimated that a 12′ length would be enough to wrap around the pipe, up to the elbow coming out of the cap. It was affordable, so I ordered it. It’s estimated to arrive on the 17th, though, so we have other things to try.

One of the things my brother thinks is a contributing factor is the new location of the ejector. The old one was about 10-15 feet away, and had a big willow overhanging it. The willow may have protected it from the elements (even though the roots were probably why it was starting to lean backwards and eventually start leaking). Right now, the ejector may be in full sunlight, but it is completely exposed to the winds we get. With the temperatures we’ve had lately, that could be a contributing factor so a slow freeze happening, and to the slow flow I was seeing in the filter. As long as some water was getting through, it wasn’t freezing completely, though, and just building up. I have a theory. The night before I discovered no flow was happening at all anymore, the septic pump had not gone off at all. Normally, between the 4 of us, plus my older daughter working at night, there’s plenty of toilet flushing, dish washing and even at least one shower. That didn’t happen, and it may have allowed for the stand pipe to finally freeze solid, and the venturi (discharge) pipe along with it.

I had already been thinking that, in the spring, I would need to put some sort of fence around the new ejector. Being so much lower to the ground, the renters cows out traipse right over it, even with the metal sheet butted up against it to divert the flow of water. My brother was thinking we’d need to build some kind of semi-permanent shelter over or around it, to protect it from the element in winter. I say “semi-permanent” as we need to assume that, some day, it will need to have work done on it, and we’d need to be able to move it.

At one point, I thought of the catio. It has a clear roof and is wrapped in plastic, making it almost a mini greenhouse. It would fit over the ejector.

Then I remembered the metal sheet. It couldn’t fit on top of that, since it has a curl to it that ensures the water flows away, and not off the sides.

But, there was possibilities.

So, while we wait for the heat tape to arrive, we need to see if we can find something we can use to build a shelter over it for this winter. My brother thinks a couple of pallets set up as a V around it, then something on top, would do the trick. We have no pallets, but he’s sure he brought some. There might also be some scrap plywood we could find somewhere.

Which means, I have a task for tomorrow. Going through the barn and sheds to see what I can find that could be used to build a shelter over the ejector. Just something we can slap together for now, but strong and heavy enough to not be blown over and destroyed by the wind. Ideally, I’d find something clear for a “roof” and add a little passive solar heat.

Trudging around outside will also give me a chance to get the truck running and see how it does! We’re warming up over the next few days, including the overnight lows, which should help, too. The day after tomorrow, my daughter and I have our joint appointment. It would be good if we could use our own truck and return my brother’s car! They really do need two vehicles.

Well, we’ll see how it goes. There’s not much else we can do!

Meanwhile, our septic tank still hasn’t filled enough to trigger the pump, so we still don’t know if the diverter will actually work, yet. It should work just fine. It’s just that we’ve had so many things breaking down for so long, now, I’m getting pretty paranoid about it all!

*sigh*

Ah, well. We’ll manage.

What other choice do we have?

The Re-Farmer

Well, it’s all we can do right now!

/ Re-Farmer / 6 Comments

Have I mentioned how awesome my brother is?

Insanely awesome. Fantastic. Amazing. What would we do without him?

After a long drive home (I think it’s 6 hours, possibly 8), he stopped only to pick up a few things, then took their second car to our place. Once here, he went into the basement to look at things there (there wasn’t much to see, really) and change into his ski pants before grabbing his supplies and heading to the barn. Right about then, my SIL showed up. Unfortunately, she’s allergic to cats, so she can’t come into the house, and just stayed in the car the whole time, though we did get a chance to talk for a bit.

My brother looked around in the barn for a while, trying to find some copper pipe. The one corner I thought I’d seen some had a different type of pipe, but there was a length of pipe were I remembered, up in the rafters. My brother was able to reach it. It was only about 6′ long, though. We talked about finding a way to add a safety line, just in case, but its surface was too smooth.

He grabbed one of their super long extension cords that they now have stored in the barn and we headed out to the ejector with the copper pipe. Then, while I secured the end of the extension cord to a fence post, he ran the rest of the cord to the pump shack, which is a bit closer than the barn.

When he finished that, he headed to the car to get the heat gun, while I popped into the house. I’d found a piece of copper pipe in the basement that had a slightly wider part at the end, so it would hold a safety line. That way, if we accidentally dropped it, we could pull it up again.

Not that we ever needed it.

By the time I got there, my brother had opened up the ejector, taken a look, then put it all back again. When I got there, he popped the elbow off and removed the cap to show me what he found.

The first obvious problem was, the venture pipe was frozen right to the top. It should have been empty. When the pump turns off, any liquid in the venturi pipe drains to the bottom, which is about 10 or 12 feet down.

The 4″ pipe around it was also full, though not quite to the top. I stuck the copper pipe I had into the opening until I hit ice to see how far down it went, and it was about 8″ from the surface.

This absolutely should not have happened.

My brother put the pieces back and we headed to the house so install the diverter.

Before we did, we went to the corner of the house on the outside to find the opening. It was higher than I expected, for some reason. I still had the copper pipe I’d brought over with me (it made for a handy walking stick in the snow!), and my brother used it to punch a hole through the spray foam insulation.

From there, it was to the basement, to install the diverter.

Installing the diverter itself was an easy thing. First, he pushed the length of pipe to the outside through the hole.

He had drilled that hole himself, years ago, when they had to do some major work on the septic system, so my parents could still use their plumbing. This is the log part of the house, which is sitting on top of those joists – which turned out to be twice as thick as he expected! It took a lot to drill out that hole.

Once that end was through the wall, it was just a matter of removing the outflow pipe at the top of the pump and replacing it with the diverter.

A simple thing – yet I could not have done it.

I don’t have a heat gun.

After loosening the clamps on the outflow pipe, my brother had to use the heat gun to soften the plastic enough to pull it off. He still had to get pretty physical with it – I was rather alarmed to see the pump being moved around so much. I’d thought it was bolted down to the concrete! Turns out, it’s bolted down to some plywood. Which makes sense, as it would be easier to change pumps that way.

Once the pipe was free, however, black fluid started spilling out. All my brother could do was try to get as little as possible on the pump itself – and not get splashed himself! Me, I immediately went for the broom we keep nearby, to sweep water into the floor drain when there’s seepage in the spring. Once I got as much as I could swept away, my brother attached the diverter – making sure to remember to put the clamps on pipe, first! After softening the plastic with his heat gun a few times, he was able to get the pipe all the way on, then clamp it down.

The next thing to do was set something up to the pipe outside, to get any outflow well away from the house. The big flexible hose (it’s about 6″ in diameter) he’d brought for us before was stored in the barn, so it would have been quite frozen. He was concerned about using it, as it might crack from the cold. There were some old downspouts in the barn, though, so he went to look and see what he could find that could be used right away.

While he went to do that, I got the hose that I use to clear the floor drain and access pipe to give the floor where the fluid had spilled a bit of a wash, and swept that into the floor drain (the floor doesn’t slope towards the drain properly). While I was doing that, I heard some gurgling from the filter as it drained. This was to be expected, though, with the pipes being switched. I left it for the moment, though, then headed outside again to join my brother.

I got there just in time to see him carrying to lengths of pipe, and dragging the flexible hose behind him! He had it by one end, so that it would straighten a bit while being dragged.

I was impressed that he found two lengths of interlocking 4″ PVC pipe in the barn. I have no idea where he dug those out!

I grabbed the flexible hose from him so he could carry the pipes more easily.

The next while was spent setting up the PVC pipe over the diverter hose sticking out of the house. It was very important that the PVC pipe be right up against the house, and as high as possible, so nothing would flow backwards towards the house. The two pieces were interlocked, and we added whatever we could find to support its weight, so that it would be completely straight. The ground slopes downwards there, so that part was fine. The very end had to be raised off the ground, so that there would be no chance of fluid freezing and blocking the end.

As for the flexible hose, that got pulled out further, so that the black plastic could be warmed by the sun, tomorrow. Eventually, it will be added to the end of the PVC pipe, and the outflow will be sent well into the trees.

For now, he made sure to shovel a trench of sorts into the snow, to direct any outflow that might happen before then. Unfortunately, he dug it straight towards our little Liberty Apple tree! I mentioned that it was there, and he was saying “fertilizer!” I said that if it freezes, it’ll kill it.

I have to add, though; this is a Zone 4 tree, and we are Zone 3. With this cold snap we’re getting right now, it may well have been killed off. We won’t know until spring!

Anyhow. Once my brother saw where it was, he just dug the trench more to one side.

Once we were sure of how everything was set up, it was back to the basement. The filter was primed, and the pump turned back on.

From there, my brother headed out to shut off lights and close up doors. He also moved the car they are leaving for us over to where I had set up the extension cord for the block heater. I helped out, then went over to the gate to close it behind them.

Now, we wait.

We can use our plumbing as normal for now. It will take at least a few days before both sides of the septic tank fill and the pill switch triggers the pump. My brother was already fretting that it might not turn on at all, but I don’t see why it won’t. We’ll just have to keep an eye on things and listen for the pump.

We are all, understandably, paranoid about using our water right now. Is it safe to flush? Can we take a shower? Wash dishes in the sink?

The answer is yes…

… but… are we sure?

At least we know the diverter pipe is right here. The pipes outside are wide enough that they shouldn’t ice up, but it would be much, much easier to take care of that, should it happen.

As for the ejector…

Well, I’ll be heading to my mother’s in the late morning, so I should be able to call the company that installed the ejector and tell them what we found. Everyone was saying how I could pull the venturi pipe out and bring it inside so the venturi valve on the bottom can thaw, so obviously no one thought the whole thing could be frozen solid the way it is. Something is wrong, somewhere.

What will come of that, I have no idea.

It will help knowing that the pump is far newer than I thought it was, and that it was the highest end pump my brother could get.

For now, though, it looks like we’ll have our emergency diverter set up for the rest of the winter.

It is what it is. We’ll just have to deal with what we’ve got! I’m just incredibly thankful that we had that diverter, and that my brother was willing to come out here tonight, after such a long drive, to do what he could for us.

Have I mentioned, just how awesome my brother is?

I don’t think I could say it often enough. My brother is the best!

The Re-Farmer

Still no change, but lots of changes!

/ Re-Farmer / 2 Comments

First, that extreme cold warning is still on, and has been extended into tomorrow.

You can see the times I took the above three screencaps, showing this morning’s temperatures. It’s coming up to 1pm as I write this, and we have not only finally warmed up to -20C/-4C, but it’s such a sunny day that the “windchill” is -15C/5F. The last screencap I took, at 9am, was just before I headed outside to feed the cats (I skipped the rest of my morning rounds), and the south facing part of the house was feeling much warmer. The wind direction just managed to be blocked by the trees to the south, which made a huge difference.

Unfortunately, we still have no septic, and the tank was not pumped yesterday, so we can’t use our plumbing. The septic truck broke down and never made it.

This morning, I tried calling one of the plumbers back – they are supposed to be available 24 hrs, according to their website. I left a message, but no one has called back.

So, we’re still using the honey pot in the bathroom. No showers and using as little water as possible to wash our hands. To do dishes, we’ve got basins on the dining room table, then we dump the dirty water outside when we’re done. We’ve even changed how we’re cooking, to try and dirty as few dishes as possible, and nothing that involves washing things, or dumping cooking water down the sink. I made a “use whatcha got” soup this morning out up leftovers – even the last bits of charcuteries meat and vegetable sticks we’d prepared extra of for New Year’s – for a hearty one pot meal.

—— pause for phone calls and messages and more calls and …. everything has changed! ——

Okay, I feel like I’m going through mental whiplash right now!

I will get to that in a moment.

Where was I?

Ah, yes. Doing dishes!

Basically, we’re being careful to have as little water going into the septic tank as possible. It can handle being at least a bit overfull – we’ve certainly gone more than a little over full just this past summer! – but we really want to avoid that.

I’m actually getting used to using the honeypot, because we can’t flush the toilet.

Yeesh.

Anyhow…

The plumber I left a message with got back to me while I was writing this. The first thing he let me know is that they are booked solid and cannot come out.

He also sounded rather upset for me. I’d mentioned the ejector was replaced about a month, month and a half ago. Ejectors are made to work in the winter. He used to install them himself. He has one himself that was installed in the 90’s, and it’s working fine. It shouldn’t be frozen. He suggested I call the company that installed it and get them to fix it. I told him I’d already talked to them, and he asked what they said when I told them it was frozen. I told the plumber that, at the time I called, we were thinking the problem was somewhere else at the time, and he was the one who suggested the ejector might be frozen. I didn’t confirm that until after. I also mentioned he’d asked me to call him back today, which I was planning to do. He told me that, when I did, to tell them they needed to come put and fix the ejector.

*sigh*

I did call the owner of the company back and basically told him what the plumber said. He was quite frustrated by that; apparently plumbers pretty regularly do stuff like that, when they don’t actually know what’s going on.

The problem is not the ejector.

The system we have works like this. The plumbing in the house all drains into one side of our septic tank. The solids sink to the bottom and, once it fills, the greywater drains into the other side of the tank. That side has a float with a pill switch in it. When it fills, the float triggers the pump inside the house. The pump pulls the greywater from the second half of the tank – this inflow pipe is where we have the filter installed, to catch any bits and pieces that might be in the water that could damage the pump – then pumps it out to the ejector. The outflow pipe runs most of the length of the basement and out the wall. The pipe, along with water pipes that supplies the heated water fountains for cattle, and a tap in the barn, runs about 300 or more feet to the barn, then turns away from the barn towards a low spot. From there, the venturi pipe creates enough pressure to draw the water up the pipe and out.

With ours, we’ve got a sheet of metal roofing to reduce erosion and divert the greywater towards a low area, further away from the barn.

That elbow at the top is part of the venturi pipe.

When the septic pump shuts off, any water in the venturi pipe drops down below the frost line and collects at the bottom of the 4″ pipe. The next time the septic pump turns on, the venturi pipe drains what’s at the bottom of the 4″ pipe first.

Here’s the problem.

There has to be enough pressure for this to happen, and that requires a certain gallons per minute rate of flow (he couldn’t remember exactly what that was). If there isn’t enough pressure, the venturi pipe can’t drain the bottom of the 4″ pipe completely. Then the pump shuts off, the water drains to the bottom, but now there’s more than there was before.

Eventually, the water level in the 4″ pipe gets above the frost line.

The septic pump, he told me, should take only about 2-3 minutes to drain the tank.

Ours takes about 5 minutes.

Except, recently, we’ve been having issues with flow.

First, the pump would empty the filter, but there wasn’t more water coming in from the tank. I would have to stop the pump, prime the filter, turn it on again, and it would work. The inflow, however, wasn’t as powerful as it had been, before.

The night before it stopped working entirely, the pump hadn’t gone off at all. The only reason it would was if we were using enough water for the second side of the tank to fill and the pill switch triggered the pump to turn on. That just didn’t happen.

So not only was the flow of water from the pump low, but there was no flow at all during one of the coldest nights we’ve had this year. Flowing water would have helped keep it from freezing entirely – at least for a while longer.

Which means that, ultimately, the problem is the pump and the flow of greywater.

Now, the pump *is* wearing out and needs to be replaced, but that may not be the problem. There may also be an air leak somewhere, affecting the vacuum. Which may have been what I was seeing, with a leak from the filter and the O ring not sealing. Or, there could be an air leak somewhere else.

Now, we could install the diverter and an emergency measure, but we still need to get the ejector thawed out, and we probably still need to replace the pump. I’ve been checking the filter regularly, and even turning the pump on for a few moments. It’s not draining, and the filter is not leaking, which – in theory, at least – means there is no longer an air leak.

Other issues could be that the pipe leading to the ejector is also getting coated with gunk on the inside and getting narrower. This is something we have been aware of and have been taking steps to try and improve. One of those was to use the Septo Bac every two days for two weeks, and we really did see a difference in how things flowed after that. Currently, we’re using Free Flow pipe maintenance twice a week; that is more to clear the pipes inside the house, but it would be beneficial for the tank and the pipe to the ejector, too.

—– Must pause for exciting news. —–

The septic guy just arrived! Our tank is being emptied right now!

We’ll be able to flush our toilet again!

I did get a peek into the tank when he popped the lid off. The level had not reached the pipe that the pill switch cable runs through yet, which was quite a relief.

That guy deserves one helluva tip.

Okay, where was I…

Right.

So there are a number of possible reasons why the ejector wasn’t able to drain properly, which resulted in the freeze.

I then got instructions on how to thaw out the ejector (that doesn’t involve ice fishing tents and heaters, as one plumber suggested trying).

I wasn’t able to pull the venturi pipe out because it’s frozen, but could rotate the cap. I couldn’t take the cap off, because of the elbow.

Well, that elbow has a screw, and it comes off.

We could take off the elbow and remove the cap.

We could then start pouring boiling water into the 4″ pipe, around the venturi pipe. However, he said to put some copper pipe down, first. The pipe itself will heat up and help thaw things out faster, but it would also help get water down more directly and further through the ice on the bottom.

Once it seems like enough ice was melted, someone could turn on the septic pump and, hopefully, it would drain the water at the bottom, and empty the septic tank.

That would take a long time, and it’s still colder than -20C/-4F out there.

—- pause for more calls —-

Oh, my goodness. More changes! This time, for tomorrow, too. I’ll get caught up to that, later.

With all this, I’ve been keeping my brother and his wife up to date, pretty constantly.

Given our concerns with the truck, another thing I had to deal with last night was how to get my mother to her medical appointment on Monday. Plus, I was supposed to come early enough to do her laundry for her. She called last night to tell me she was able to get her laundry done herself and that I didn’t need to come early. I told her a bit about what was going on (I didn’t want to overwhelm her!) and that I wasn’t sure if I could get her to her appointment. She tried calling my sister to drive her (which she didn’t want, as I’m the one who normally accompanies my mother, so I’m on top of what’s going on), but my sister starts her shift at work less than an hour after my mother’s appointment.

I passed that on to my brother as well. Today, I was supposed to run the engine a few times, so see if the problem continued, then decide Monday morning, if I’d be rescheduling my mother’s appointment. Possibly mine and my daughter’s on Wednesday, too.

I got a call from my SIL. They were going to be coming home on Sunday (today), and she offered to drive us. She would pick me up first, then we’d pick up my mother, drive her to her appointment, then she’d drive us both home again, then head home herself.

I was stunned by the offer – that’s a LOT of driving for her! Once I was sure this would not be too much of a problem for her, I gratefully accepted the offer.

Today, I’ve been messaging them the whole time, while they are on the way home. My SIL was driving, so my brother was able to respond to my messages.

When I told him about thawing the ejector and needing to look for a long enough copper pipe (I know I’ve seen some, somewhere!), he called me. I was just bundling up to go outside and check the barn.

Which is jam packed with their stuff.

I’m sure there is one long enough in one corner of the old bull’s stall, but it’s full of my brother’s gardening supplies now. I wasn’t sure if it was there, and I wasn’t sure if I could reach it! I’m pretty sure there are lengths of copper pipe in the rafters, too, but again, I’m not sure I could reach them. The centre aisle of the barn is full of tractors and snow blowers and rotary mowers, and I’m… well… short.

My brother called to tell me not to bother trying to thaw out the ejector. They would go home, then come here with both their cars. My SIL would follow later. He would take a look at the ejector, see what he could do, then she would drive him home.

They would leave one of their cars with us. It’s already parked outside, so they know it can handle the cold.

My truck should, too – it certainly did last winter! – but that’s another story….

The thing is, they were still about 3-4 hours away from home! Add in the time to come here, and he won’t get here until after dark!

But he felt he had no choice. No one is coming out to install the diverter, and no one was going to come out to thaw out the ejector. The one company would have, but they are so far away, it would be a lot more expensive, and they didn’t want to ding us with a huge bill. It’s not like they’d be coming out to fix an actual problem with the ejector they installed, that would be covered by any kind of warranty.

Plus, by leaving us with their car, my SIL won’t have to do all that driving.

Then my brother told me to sit down with a cup of tea and relax for a while. He knows me well enough to know how all this has been stressing me out.

Which is about when my husband called out, saying “are you expecting someone with a big truck?”

I’d opened the gate for the septic truck last night, and never closed it. He was able to drive right in!

He’d backed into the yard, so I threw on my parka and headed out. We went over to where I’d cleared things to make room for the truck and the hoses, and got the insulated tarp freed from the frozen ground. He then went to back the truck up the rest of the way. I confirmed how much we owed him, and told him it might be a couple of days before I can get the cash to him. He was fine with that. We’ve done this before, and he knows he can trust us.

With that, I went back inside and let my brother know the septic truck was here. It didn’t take him long at all to empty the truck, so when my brother said he wanted to call, I delayed it long enough for me to go back out, put the weights back down on the tarp, which the septic guy had put back, and put everything away.

Not before using the toilet and actually being able to flush it!!!

Ooooo… Very exciting! 😂🤣😂

While it was great that the tank was emptied, it does make thawing the ejector a bit more complicated. It will take probably a few days before both sides of the tank filles enough to trigger the pump again. Which means that, if we thaw the ejector, there’s not way to test it.

My brother thinks he should be able to use his heat gun and the copper pipe to thaw the ejector.

We’ll see how it works out, though. We won’t really know what we’re dealing with until we get that cap off and can actually see how high the ice it – or use the copper pipe to find how far it goes.

When they reach their place, he’ll grab a few tools, but we really only need a screwdriver to remove the single screw to get that elbow off.

Of course, things never turn out as expected, so who knows.

They don’t have a lot of tools at their place right now. They brought most of them here, to the farm. However, they’re scattered all over. They didn’t have time to be organized about it, but just jammed things wherever they could. My brother won’t be able to start organizing things until spring, at the earliest.

Well, we’ll do what we can with where we are at.

Meanwhile, they will be leaving a car here, and it will need to be plugged in. So I headed out to the garage to get a 100′ extension cord and set that up through the back door of the garage, so the car can be parked in the more sheltered yard.

While I was at it, I finally got to the truck and got the engine running. Then, after puttering with the extension cord, I set up my OBDII scanner.

The first thing I noticed was that the oil pressure gauge was still sitting at 0 and not moving. The check engine light was on again, too.

I did a full module scan. What I’m getting is “Engine Oil Pressure Sensor/Switch “A” High. Five times.

Looking into more detail, the scanner tells me this code frequency is “very common”. The recommended fix is to replace the engine oil pressure sensor.

Which got replaced not that long ago. Unless “switch A” is a different sensor.

I took screen captures of the results. When I’m somewhere with enough data signal to send images through text, I’ll send them to the garage.

Otherwise, the truck sounded just fine. In fact, now that the MAF sensor has been replaced, I do hear an improvement in how it starts, when using the remote car starter. Definitely smoother. I’d checked the oil yesterday, and it was fine, too.

Phew.

This post took a lot longer – and became a lot longer – than I expected!

As of right now, I’m basically just waiting for my brother to arrive and will accompany him to the ejector.

My brother is the best. So is his wife! I am so glad my mother transferred ownership of the property over to them. I don’t know what we’d do without them!

The Re-Farmer

How many things can go wrong at once?

/ Re-Farmer / 14 Comments

Someone just shoot me know. Put me out of my misery.

No, I’m not serious. Just hyperbole, but really?

So we’ve got our septic issues. The pump never turned on during the night. I did check it, and found that m it wasn’t until late morning that I finally heard it turn on, and I immediately went down to check on it.

There was no flow through the filter. In fact, it was still full and nothing had drained out the bottom.

So I did the usual. Shut off the pump, pop the cap off the filter to fill it…

There was no seal.

I primed it, turned the pump back on…

There was no water flow. Nothing.

At this point, it was looking like we needed a new O ring. I’ve been messaging my brother through all this, and he suggested using Vaseline to get a seal. I found a tiny little jar of Vaseline in the bathroom and gave it a try.

Still no seal, still no flow.

I then spent I don’t know how long, calling hardware stores, looking for a 5″ O ring.

No one had.

Even the one in the town to the north of us, which I knew carried their own version of a septic pump filter, didn’t have one. They had a 6″ one.

They did recommend I call an auto place on the same street as them, as they carried all sorts of O rings.

The first question I was asked was, how thick. I never even thought of that, because all the places I called basically had one thickness. It was never a question. I gave the closest I could and he went looking.

They had one.

Yeah!

I started heading to the truck to head out.

As I was unplugging it, the first thing I notice is the front driver’s side tire is really low. So I fire up the compressor to pump it up.

That poor compressor. It was NOT liking the cold!

I got the tire pumped up, then got the truck started to warm up while I opened the gate. As I’m backing the truck out of the garage, I see something odd.

The oil pressure gauge is at 0, and is not moving. At all.

I stopped most of the way out of the garage, so I had room to set up the foot stool to check the oil.

It was fine.

I started the truck again, and the gauge still wasn’t moving. I left the engine to run while I went inside for a bit. I tried calling the garage, but it went to voice mail, so I tried sending a text, instead. Then I went back to the truck.

Now the check engine light was on.

*sigh*

I did not have time to fuss with this. I parked the truck, plugged it back in, locked the gate and headed inside.

Then I started calling plumbers.

Long story short, after getting through to one place and explaining the situation, they recommended someone in the town where the O ring was. I called there and left a message.

Then I went to the basement to try the pump again.

As before, I turned on the pump, but nothing was flowing through the filter. So I shut it off and opened it up.

It was sealed so well, I had to pry it off. It took a while, but the Vaseline made the difference.

I checked things and even switched out the filter baskets, even though that had been done recently, so the one in there was still pretty clean, closed it up and tried again.

Still no flow.

So the problem was not the filter, after all. And the pump seemed to be running pretty normally. So why wasn’t any water flowing?

I ended up calling the first plumber I got through to again, talked to the receptionist and explained what was going on, which she passed on.

At this point, I had so many calls and return calls to so many different places – including the company that installed our new ejector – that I’m starting to get them mixed up.

Long story short, it was suggested the ejector might be frozen. With suggestions and advice from different places, I headed out with a couple of jugs of hot water to see.

From how the ice and snow was on the diverter, clearly the expeller had been working all right until now. It obviously had quite a bit of pressure to create that ice wall so far from the expeller.

The cap is held in place with two screws, which I removed.

It was frozen solid. I couldn’t even rotate the cap.

I poured hot water over it and was eventually able to rotate the cap, but the venturi pipe would not move. I didn’t want to use too much force on it, or it would crack in the cold, but there was no way I could remove it to thaw it out, or to pour hot water into the pipe.

This is a serious problem. There is no way we can thaw this out, which means no septic for the winter.

I was keeping my brother updated through all this, though he’s currently out of province. When talking about the possibility of the ejector being frozen, he brought up something I completely forgot about.

With the problem we were having before, he’d brought over a massive hose for the diverter.

We could set up the diverter, if necessary. We would bypass the ejector system completely. A diverter pipe would be attached to the pump and run out hole in the wall, which is currently filled with spray foam insulation. The hose he’d brought over is now stored in the barn. We could set that up and the pipe from the basement would get drained into the maple grove for the winter.

With the ejector being frozen solid, that is now our final option.

More phone calls needed to be made.

One of those calls was to our septic guy. We need to get the tank emptied, since the pump can’t drain it. We can’t use our water. We still are, for small things, but no showers or doing dishes, and even flushing the toilet has to be avoided.

Thankfully, they will be able to come out today, so we won’t have to set up the honey pot. They’re a cash only business, though, and I don’t have any, but I can pay them later, which is something I’ve done with them before.

It will take a while for them to warm up the truck and get here, as this cold is causing all sorts of vehicle problems for everyone. As I write this, we are under extreme cold warnings, still. The temperature is at -21C/-6, and the wind chill is -29C/-20F

Once the tank is emptied, we’ll have a bit of a grace period and can use our water while waiting for a plumber to come in.

So far, I’ve had one tell me they’re booked solid for 2 weeks. I’ve left a message with the other, explaining what I needed and asking them to call back. I’ve also gotten through to the company that installed the ejector and asked if they could install the diverter for us. They are the furthest away and would be charging mileage, so he suggested I keep calling others. He then asked me to call him back on Sunday evening to update him. If I can’t find anyone, he’ll have someone come out. Otherwise, he wanted me to let him know if we found someone closer.

Which is where we stand right now. The septic guy hasn’t arrived yet, but I was able to get the insulated tarp over the tank lid freed of ice and snow and pulled back far enough to access the lid. Then covered it again, until he gets here.

As I write this, I realize it’s been at least an hour since the septic guy called me back. I hope he’s okay!

The extreme cold warning extends into the wee hours of tomorrow. We’re supposed to have a high of -19C/-2F tomorrow afternoon, and the days are supposed to keep warming up after that.

Just checking the weather now, and we’ve already dropped to -22C/-8F with the windchill now at -31C/-24F. Which could be worse; some places are getting wind chills of -40C/F

It’s past 3pm as I write this. I’d better go top of the kibble for the outside cats and – more importantly – give them more warm water. A lot of the kibble bowls are still really full when I head out. The ones in the kibble house may be sheltered, but there is no warmth. The bowl in the catio, wrapped in its plastic, gets emptied, but now the bowls under the nearby shrine. I’m rather surprised the plastic is making that much of a difference. The bowl in the isolation shelter gets emptied completely. So I try to leave more food at the bowls that get empties, so they don’t have to go into the cold to eat. I want them to stay warm and cozy as much as possible! Their winter fur is obviously helping, though, as I’ve been seeing them all over while outside.

What a day.

How many things can go wrong?

Don’t answer that. I don’t want to know!

The Re-Farmer

Some things don’t take a break for Christmas!

/ Re-Farmer / 2 Comments

I hope you are all having a wonderful Christmas day!

First up, I will share the cuteness with you.

The yard babies are enjoying a roasty toasty Christmas in the isolation shelter.

After taking the above video, I fixed the hammock and tried again.

We had our non-traditional Wigilia dinner last night, so today, the outside babies will be getting some turkey bits, including the innards, for a treat. I’ll be deboning the turkey and making a stock for them.

Not right away, though. I don’t want to go anywhere near food right now. I’m feeling really gross and disgusting, even though I’ve washed up several times.

I discovered the septic back up the basement floor drain, today.

*sigh*

That’s what we get for falling behind on running the hose through the floor drain to the tank regularly.

For the past while, we’ve started hearing gurgling from the tub drain every time we flushed the toilet. Knowing that the main drain pipe from under the tub to where it turns and drains into the septic tank, this isn’t surprising. It kept getting worse, though. I checked the vent in the roof and it was clear of ice or snow, so that being a possible contributor was ruled out. I even plunged the bathtub drain. After a while, though, I finally decided to go into the old basement – something we don’t do often enough, but those stairs really suck.

Which is when I found the mess. Things were starting to back up through the floor drain.

Thankfully, it hadn’t been doing that for very long.

So I opened up the access pipe and tried running the hose we keep set up to flush the pipe through. There are two bottlenecks. The first is just a couple of feet from the access pipe opening. That one doesn’t usually get blocked, but it takes a few tries to get the hose through. The second bottleneck is about 5 or 6 feet through, so pretty close to the tank itself. The pipe in the floor is cast iron. At some point, it attaches to the more usual plastic pipe. I have no idea how long the cast iron pipe it, but I suspect the second bottleneck might be where the two types of pipe join. Either that, or it’s right before where the pipe enters that tank.

That’s the bottleneck that gets blocked.

This time, I couldn’t get the hose through at all. Normally, I’d run water while doing this, but when I did turn the water on, it just started backing up the floor drain more.

I could have set up the drain auger, but that would have had it sitting in water – something the instructions said to avoid, if possible. I didn’t think it was necessary, though. We have an old chimney sweep rolled up in the corner. It’s just thick, stiff wire with a brush at one end. The other end has the tip bent back on itself. That’s the end we push through the pipe. Using that, I was able to break through the clog. I could tell when it worked, because the floor drain started to immediately empty.

After getting the wire out, I was able to run the hose all the way through, with water running. Given the lengthy of hose I was able to get through, it was going all the way into the tank, and then some.

From there, it was time to clean up the mess I didn’t want going into the floor drain, then flushing that out. It’s a 4 way drain, but only two are used. One runs to the weeping tile under the new part basement, the other to the septic tank. The two unused drain sections run about 8 or 10 inches before they are blocked by concrete. All of these needed to be flushed out. Then the pooling water on the floor needed to be swept into the drain and cleaned.

One of our goals it to cover the floor with self levelling concrete to get rid of all those low spots. Considering the concrete walls themselves are crumbling, I sometimes wonder if it’s even worth it.

Anyhow.

All that got done and cleaned up, and a blower fan set up to dry the floor faster.

Once in the bathroom to clean up, I did a test flush on the toilet.

Zero gurgling from the tub drain.

So that was the problem all along.

*sigh*

Our own fault. We fell behind on the flushing of that pipe. I’m just glad it didn’t start backing up earlier, such as while someone was taking a shower or something.

I think I’ll be asking the girls to do all of our Christmas dinner today. Usually, we split up doing different dishes between us, but I just don’t feel up to handling food, no matter much well I’ve scrubbed up!

We had a turkey dinner yesterday, finishing off the last of our garden potatoes. Today, we’ll be having smorkchops (smoked porkchops).

Oh, and just to top things off, after messaging my family from the basement to let them know what happened, I put my phone in my pocket…

… and it fell out.

It has a wallet style case with a cover on it, which protected it to a certain extent, but I’ve got the moisture warning saying to let it dry before plugging it in. It’s now out of its case, all cleaned up, and sitting until the port is dry. It also has a screen protector, but there is now a small chip on the bottom – I have no idea how, as that spot should have been covered by the protective case. There is what looks like a small crack, but I can’t tell if that’s the screen, or the screen cover.

The phone still works, though, and it’s not interfering with anything, so I don’t care too much.

So… that is how my Christmas has been going!

I’ve been talking with both my daughters as I write this, and they are taking over all the Christmas cooking today!

Oh, how I wish I could take a bath.

Days like this, being broken really sucks.

No matter. All is good.

Merry Christmas!

The Re-Farmer

Testing, testing…

/ Re-Farmer / Leave a comment

Yes! We have major progress!

But first, the cuteness.

I did my evening rounds after giving the outside cats their evening feeding. As I was coming back to the hose, I saw this adorable face watching me.

We can most definitely consider Kohl well socialized now – and boy, does she ever want to get into the house! It’s a good thing we have the old kitchen as a buffer zone. She and several others often manage to dash inside while I’m struggling with the doors and a bowl full of warm kibble for them.

The Cat Lady was asking me if we could be able to catch any females for spaying this fall. Among the kittens, we should be able to easily catch at least two – Kohl and Magda – and possibly a third. There’s also one adult female we should be able to catch, but the clinic that we’ve been going to has special pricing for spaying cats under 6 months old now. Kohl may be too old for that now, though. She is from the very first litter of the year.

Meanwhile…

I’m happy to say, the parts and pieces of plumbing for the tup that needed to be replaced, have been replaced. We were able to attach the fixtures, turn on the water and test it out.

While my daughter was working on the other side of the wall, I stayed on the tub side to turn things on and off whenever she told me to. I took advantage of the wait in between to scrub and clean as much as I could, then scrape off any remaining old caulk that I could find. In the process I discovered that I could scrape off much of the rust and scale that had accumulated under the hot water tap when it leaked during use. CLR wasn’t getting it all for a reason!

After the first test, we found that the cold water was leaking at the tub, while the hot water was leaking at a Pex to copper join in the basement. My daughter spent the next while tightening and taping everything, while getting me to turn the taps and shower on, as needed.

It looks like we finally have everything tight and leak free!

My daughter is just amazing. She was working in some really tight spaces. Especially in the basement, which had the added issue of cobwebs to deal with, even though she did sweep away most of them, first.

My daughter does not do well with spiders, so her doing that is really, really something.

Once the testing was done, the water was shut off again, and the fixtures removed again.

The next step will be to add mold and mildew resistant sealant around the tub edge, in the corners, and anywhere else that looks like it needs it. I will be bringing some wood lath over from the garage to place in strategic areas where the paneling was cut out, so the tub surround will have something to adhere to in that area. Only if it’s thin enough, though. It might be too thick. We shall see.

If we do add the wood, the cut out area will get another coat of the mold and mildew resistant primer.

Then, once everything has had a chance to dry and cure, we will finally be able to install the tub surround.

Last of all, we put back the arm bars.

In between all that, we need to pick up a couple of heat elements for the hot water tank. Hopefully, that will be enough to get us hot water again. I would hate to have to buy another tank, considering how much the price has increased since we got the last warranty replacement in 2020.

I’m not sure when we’d be able to do this, though. I got a call from my mother tomorrow, telling me “her fridge is empty “my fridge is empty!”

She isn’t actually out of food; that’s just her way of telling me she needs a shopping trip.

Still, she was wanting me to come over today! I told her I was going to be helping with the plumbing today, so it’s arranged for tomorrow. She has her Meals on Wheels coming in tomorrow, so I don’t need to leave as early to pick up a lunch for us. She still needs to get to the bank; she wasn’t up to it last time. I was hoping my sister would have been able to come over with her smaller car to help her, but she and her husband are out of province right now. So my mother will have to clamber into our truck again!

I’m not sure how long I will be gone tomorrow, but I still hope to get at least a little bit more garden clean up done. Tomorrow is supposed to be a bit cooler than today was, but it’s then supposed to warm up for a few days – there’s even a high of 21C/70F in the forecast! – so I hope to get more done on those days and, if all goes to plan, start direct sowing seed for next year’s garden.

We shall see!

Meanwhile, I’m going to start heating up water so I can actually bathe. The tub now is clean enough to use instead of the sink!

Man, we have had to heat water to bathe way to many times since moving out there! 😄😄

The Re-Farmer

Well, that’s not gonna happen, and we are SO lucky!

/ Re-Farmer / Leave a comment

I’m just pausing to write a quick post, before I go to help my daughter with the bathtub plumbing.

We got the new hot water tank element tool out just a little while ago, and headed into the basement to see what we could find in the two older tanks. The hope was to be able to use one of the elements from the old tanks to replace the burnt out one in the current tank.

Yeeeeaaaahhhh….

That’s not gonna happen.

This is what we pulled out of the first tank, where I’d already opened up the panel for the top element. The bottom one was encrusted in scale on the outside, so that one was clearly not going to be good.

Click through to see the other side of the element.

Wow.

Yeah, that’s toast.

So we opened up the panel for the other old tank.

The first warning that things were not good was that I had to tear the panel free of the insulation.

The outside of the insulation had rust on it, and we could see damage to the wires.

After tearing away most of the insulation, this is what we found.

Yeah. That plastic cover is melted. That thermostat is burned.

Click through to the next image, and you can see more of the damage, and how completely encrusted the outside of the element is!

It is an absolute miracle that there wasn’t a fire started.

As for the current tank, we no longer even have warm water, so we’ve shut the breaker off. It looks like both elements are burned out now. Seeing what we pulled out of the old tank, I’m not at all surprised!

When the first tank died, it was after less than 2 years of use, which is why we were able to replace it on warranty. About a year later, when we saw the replacement tank starting to leak on the bottom, we were able to replace that on warranty, too, even though we should not have been able to. We kept the new tank in the box until the second tank finally died. It lasted far longer than we expected.

I just looked up my old posts. This current tank was installed just over a year ago – Oct. 10, 2023, to be exact. We were able to pick it up as a warranty replacement in April of 2021. Before that, we got a new tank in January of 2020, though it took a bit longer before we could get it installed. The tank that was originally here was replaced in December of 2017, just in time for Christmas. All four of us had been here for little more than a month at the time!

Not counting the original tank – I found the original warranty papers for that, dated 1963, if I remember correctly – we have gone through 3 modern tanks in less than 7 years of living here.

The most recent one lasting just over a year after installation.

That. Is. Insane.

It all really comes down to our water. I remember talking to the plumber during one of the installations, and he told me that this is pretty typical for hot water tanks in our area.

When all this started, these tanks cost a little over $400. Looking at them now, I see they cost about $700 for the exact same tank.

The elements cost about $40 each.

With the powered anode rod that should arrive next week, that will hopefully keep the tank going longer, though we still need to get the right tool to remove the old anode rod. I thought the tool we got for the element might also work for the rod, but it’s way too big. We need to buy the right size socket to be able to remove the anode rod.

For right now, though, I need to go help my daughter. She was able to get the piece out that needed to be cut out. With the adapters, we might not even need to replace the copper pipes to the basement, though the hot water one has the 90° elbows in it, so that one should probably be replaced with Pex, at the very least.

But I digress!

Time to go assist my daughter.

The Re-Farmer

Garden clean up started, and water woes update

/ Re-Farmer / 3 Comments

Today is the first of a short spell of warmer days we are expecting. As I write this, at almost 7pm, we are at a lovely 12C/54F. The weather app says it feels like 5C/41F, but it doesn’t seem that chill around our home.

This afternoon, I took advantage of the warmer temperatures and finally got to work, cleaning up in the main garden area. What I’m shooting for is to get some beds ready to try some fall planting – because garlic, that is. I’ve been inspired once again by Gardening in Canada.

The more we can get done in the fall, the easier it will make things in the spring!

I’m surprised by just how much can be planted in the fall, with our zone 3 winters. Her list includes wildflowers; particularly poppies, hollyhocks, sunflowers, coneflowers and columbine. Now that I think about it, all of those make sense; we’ve had all but coneflowers sow themselves here, and the only reason we haven’t had coneflowers overwinter here is because we don’t have them anywhere to begin with. I do still have a native wildflower mix that needs to be sown, but those will have their own space to be seeded in.

For vegetables, she listed them in groups. One is the alliums; onions, leeks and shallots. We’ve got our own onion seed this year, so that is an option for us. We should also be able to use our own garlic for planting this year, too.

She mentions root crops like turnips, carrots, radishes and beets, all of which benefit from winter sowing by becoming sweeter and more flavourful, the following year.

Peas is something she plants all over, as she uses them as an indicator plant. You can tell how warm the soil is becoming by when they germinate.

The next group she mentions are brussels sprouts, kale, spinach, kohlrabi and possibly cabbage.

Last of all, she mentions squash and pumpkins. Considering the squash we had in our compost pile last year, we’ve already had those by accident!

They are normally a hot weather plant, but our compost tomatoes shows that, in the right conditions, tomatoes could be added to the list, too. Hmm… so can beans, for that matter.

Looking at her list and remembering what I have for seeds right now, we could plant onions, turnips, carrots, radishes, beets, peas, spinach, kohlrabi and both summer and winter squash.

What I might end up doing is just mixing up the seeds for onions, turnips, carrots and beets and planting them randomly in one bed – mostly because the onions could protect the things it’s planted with from deer. I could probably interplant onions with kohlrabi, peas and spinach, too, though I’d have to watch the spacing more. Squash… well, they take up so much space, they would be on their own, for the most part!

In order to do this, there are two things I need to get ready. First, is prepare the soil by increasing organic material. Compaction is a huge problem with our soil. I can do trench composting again, which really seems to make a big difference in production, but the soil itself needs to be amended as best we can.

Then, once seeds are planted, the other thing they will need is a light and fine mulch. Grass clippings and leaves would be what we have on hand to use. She recommends piling snow over the seeds in the winter for added insulation, but for the main garden area, I don’t see us needing to do that. That whole space gets well covered with snow over the winter!

Right away, I can see that we would have a very different garden next year, if we do this fall sowing.

We shall see if we can get to that point over the next week or so!

With that in mind, I focused on the main garden area. Here is a slideshow of today’s progress.

I started off using the weed trimmer. I hadn’t been able to do much clearing of the paths, once the winter squash, pumpkins, drum gourds and melon bed vines really took off. In some paths, I could barely walk through them without stepping on a vine.

I started to use the weed trimmer in where the next raised bed that will be part of a squash tunnel will be built, but not too much, just yet. I’ll clear into there more when I have to access the stack of what will be vertical support poles attached to the existing bed.

After trimming one side of the high raised bed, I stopped to pull up the winter squash vines. All the squash got powdery mildew towards the end of the season, so all of these were for the burn pile, not the compost. In fact, the only squash that did not get powdery mildew was the Crespo squash, in a completely different area.

I ended up spending most of my time on the pole bean trellis. There were only 5 surviving plants but, my goodness, they sure took over that trellis netting!

Also, folding up that netting for storage is a lot easier when you lay it out, then weave a bamboo stake through one short end.

After the first squash bed was cleared, I moved the corn stalks over from the other squash bed, so I could get at the vines under them. Later, I plan to trench compost the corn stalks.

Pulling up the squash vines was truly interesting, at times. I couldn’t believe how long some of them had gotten! These would have been so awesome on a trellis tunnel!

The only two beds I did not clear this time were the high raised bed, and the first trellis bed. I did finish weed trimming the paths, though. Right now, the bed that needs the least amount of work is the westernmost one, where I’d already prepped half of it after harvesting the onions and covered it with plastic.

The solarization doesn’t seem to be working, though. I’m seeing a lot of green growing under one end. The problem is, that end of the bed gets a lot more shade, this time of year, so it doesn’t get a chance to get hot enough to solarize. At least not at the south end. There may be greater success towards the middle of the bed.

Around the time I finished the weed trimming, I found some messages from the family. My daughter had spent some time going through all the fittings I picked up, working out which would be needed, which wouldn’t, etc. In the end, we were going to need more of two fittings – and will likely have quite a few to return to the store, once the job is done.

It was past 3:30 by then. The store we needed to go to was the second one I’d gone to, yesterday. Thankfully, they weren’t going to close until 5:30 – the local one closes at 4. My daughter came along with me.

While she was looking at the fittings, I looked around for the hot water tank element tool I needed, then asked for help, because I couldn’t even find the section. It turned out to be tucked away in a corner. 😄 I also asked about a socket large enough to remove the anode rod but, in the end, I think the same heat element tool will fit the anode rod. I’ll test that out, later.

Then my daughter needed help, because one of the fittings she was looking for was behind locked doors! Quite a few displays in this store were behind glass. I would not have expected theft to be more of a problem in this location, that the store I usually go to!

After we got what we needed and were heading home, I missed my turn to cross over to the other highway – the streets look no different than driveways in this town! That meant we ended up driving to the town closer to home.

My daughter hadn’t eaten anything since early in the morning. Since we ended up in town anyhow she, being the sweetheart that she is, sprung for some Dairy Queen for all of us.

It now looks like we have everything we need to replace the pipes and faucet set for the tub. The hard part is going to be cutting the copper pipe to get the old pieces out. There is very little room to work in. Especially since the cutter needs to spin around the pipe.

While I might be able to assist, this is a job mostly for my younger daughter. She’s the most able bodied among us – and considering she has PCOS and all the joint pain that can come with, that’s not saying much!

Hopefully, I will be able go get more progress in the garden instead, and if all goes really well, be able to plant things for next year in a few days!

If all goes well for my daughter, we might even be able to use the tub and shower again, soon, too!

We shall see!

The Re-Farmer

Progress! But still no shower or hot water

/ Re-Farmer / Leave a comment

Okay, so we DID get progress today. Honest!

My main thing was to go into town and talk to my favourite manager. We spent a lot of time looking at the photos I took of the bathtub plumbing, and things like whether or not we will be replacing the copper pipe for the shower with Pex as well as the hot and cold water pipes. Plus, we’d need to replace the pipe to the spout, which is completely different and would be removed with all the other old parts, since it would be soldered in place with lead, too.

My brother had talked about using Shark Bite fittings, but the manager suggested it would be better – and cheaper – to use Pex crimps. That meant getting a crimping tool, which is something we’ll need in the long term, anyway, and a Pex cutting tool. I wish I had that when I bought Pex (a different type) to use on one of the raised bed covers.

As we went through various fittings and joins, crimps and, of course, the Pex pipe, etc., there was one type of fitting they only had two of. We figured I would need at least six. He called another store for me and confirmed they had plenty in stock, so once I was done with the local store, I drove to the next town up the highway to get the rest.

He assured me that, anything we don’t use, we can return. Just hang on to the receipt for both stores, because if we want to return anything, we would have to return them to the store we bought them from, even though they are the same franchise.

I am really hoping we got everything we need.

While I was doing that, my younger daughter scrubbed the exposed walls around the tub, treated it with an anti-mold and mildew spray cleaner, then left the fan running on it. She did that a second time and, when that was dry, she started painting the exposed walls with the mold and mildew resistant primer. So far, that has two coats. I think it’ll need a third.

Once that is done, it will be ready to have the tub surround installed – whenever that will be!

Once I got home, my daughter and I went through the parts and pieces. I was already forgetting what was what. My daughter knew what she was looking at, though.

Having daughters that both used to work in a hardware store comes in very handy at times!

She was in between coats of paint, so I grabbed some tools and headed to the basement. I wanted to see if we could use one of the top elements from the old hot water tanks, and see how to remove the anode rod.

*sigh*

Since both tanks died because they started leaking out the bottom, the bottom panels were already open. Damage on those ones is visible from the outside. I uncovered the top panel on one of the tanks and removed the wires to get a good look.

Hmmm…

After consulting the manual, I realized I would not be able to take them out. There is a special tool – basically, a large socket – to remove them, and we don’t have one.

So I shifted to the anode rod.

Now, this is supposed to be easy. Pop off the cap, remove the anode rod and you’re done.

The cap did NOT want to come off.

I should have been able to slide the tip of a Standard screwdriver under the edge and lever it up, but the edge all around the cap just bent. Eventually, I was able to jam the screwdriver down between the edge of the cap and the metal and pop it off, breaking off something under it in the process.

The opening was full of foam insulation. Oddly, there seemed to be text in the foam. I had to take a flash picture of it to be able to see that yes, there was writing – and it was backwards. Looking at the underside of the cap, I could see the writing that was imprinted into the foam insulation.

There was nothing about this in the manual.

I dug out the insulation until the top of the anode rod was finally uncovered.

Oh… something else that needs a socket.

Back to the tool kit I go and come back with the largest socket we’ve got.

It wasn’t large enough.

*sigh*

So I wasn’t able to get either the rod or the heat element out. With the rod, I just need to know how to do it, for when the powered rod comes in and we replace the one in the current tank. I’d hoped to get the heat elements out and see if at least one of them is still good, so we can switch it out for the burnt out one in the current tank.

I guess I’ll be going back to the hardware store tomorrow. The tool for the heat element is $25. A large socket ranges from about $9 to $14.

I’m certainly glad we still had the old hot water tanks in the basement that I could use to find this out. It would have really sucked to find this out on the current tank!

Since I couldn’t do any more there, it was time to finally start putting away and cleaning up in the garage, so we can finally park the truck in there again, now that the cat isolation shelter is out.

When bringing stuff to store here at the farm, my brother brought me a couple of crane boxes. I have no idea what makes them a “crane” box, other than they are rated to hold up to 1000 pounds. One of them got crushed a bit, but it was still useable. They actually came in handy as surfaces I could use to hold the clear plastic for the isolation shelter. I was able to cut in a gap between the boxes, and have weights on either side to reduce vibration. It worked really well.

The garage walls are unfinished, with exposed joists. When I moved off the farm, the garage was just a single “room”, all the walls were exterior walls, with shiplap boards covering the outside. Over the years, lean to additions were added to each side.

My brother had brought scrap wood they were intending to add to the burn pile, but there was a lot of useful wood in there that I kept, instead. From those scraps, I was able to cut three supports per box and attach them to wall joists, using the shiplap boards as a guide to keep them even, since I didn’t have a level with me.

The boxes each had three “feet” on their bottoms that reached from side to side, made up of stacks of what looks like plywood, nailed and glued together. Unfortunately, they were spaced in such a way that, while two of them could fit in the space between the wall joists, the third one did not. So each box had to have one of these “feet” removed.

That was NOT an easy job. They were nailed together from both the inside and the outside, plus the inside had extra long staples into them.

I had a pry bar handy, though, and was able to get them off.

Once that was done, I could put the boxes on the supports, with the bottoms against the joists. They then got screwed directly to the joists, as well as the supports.

The supports are all longer than the boxes are deep. The boxes have lids. Once I get some larger hinges, I will attach the lids with hinges on the bottoms. This way, they can be opened from the top to form a surface. It will make it harder to reach what’s inside, but I figured having that would be useful enough to be worthwhile.

Once the boxes were hung up, I had someplace to start putting things on my work table away, rather than returning them all to the sun room. Last winter, the cats knocked way too many things down to the ground, so I want to avoid storing things there, if I can.

Here is how it looks like now.

Eventually, we’ll be making more shelves against the walls, and I will be able to clear the space under these boxes. That’s all on a makeshift shelf that’s just a piece of scrap plywood sitting on top of a couple of 5 gallon pails on their sides. It was meant to be temporary. We just haven’t gotten to working on organizing the garage, yet. There’s just too much stuff in there that I have no idea what to do with.

These boxes have enough space in them that we could probably add another shelf across the middle. Maybe in just one of them, and leave the other open for larger items.

That done, I was able to finish clearing off my work table, saving some of the wood scraps for future projects, while others will go to the fire pit, moving the miter saw, and so on, and the work table got folded up and set on the swing bench in where my mother’s car is stored.

The saw horses that I’d been using while painting now had a screen over it to hold the curing shallots. My daughter wants them to cure a while longer before braiding them, so that got moved in front of the swing bench.

Then came the finicky part.

Getting the floor safe to drive on.

I’d already fired up the compressor to pump the flat tire on my mother’s care, then used the air to clear off the sawdust on the work table. For the next while, I used the compressed air to blow away the sawdust on the ground, too.

I’m glad I did, because I found quite a few shards of glass in there! I have no idea where they came from, or how long they’ve been there.

Eventually, I got to the point where I could start raking the dirt floor, and used a magnet to find any nails or other metal bits that might have been lost.

I had to consider what to do with my brother’s lawn tractor. There isn’t room for it in the lean to’s on either side of the garage, and I don’t want it stored in the barn. I ended up moving some bins to the other side of the garage, where they are now being used to hold recycling. There was a lot of weird odds and ends in the ground under them, like rusted out bolts and very old spark plugs that predate us living her for quite some time. The area got raked and cleaned and raked again before I went over it with a magnet.

In the end, I still wasn’t confident in the space. I had rolled up the protective cover that the clear roof panels were wrapped in. It’s got a waterproof surface on one side. I decided to lay that out on the ground against the wall, and that’s what the lawn tractor is now sitting on, close enough to the wall that the truck has plenty of space.

After a bit more raking and a bit more searching with the magnet – and finding more bits of glass in the oddest of places! – I was confident enough to get the keys and park the truck in the garage.

Finally!

By the time that was all done, my daughter had finished more coats of paint in the bathroom.

So while we still don’t have the plumbing fixed, we still don’t have hot water (though if we leave it long enough, we do have very warm water at times), we did get some good progress today.

The next six days are supposed to be warmer, so I’m hoping to be able to finally work on cleaning up garden beds, but if my daughter needs help with the plumbing, that’s the priority.

Little by little, it’s getting done!

The Re-Farmer

Well, that isn’t going to work!

/ Re-Farmer / Leave a comment

First, Happy Thanksgiving to my Canadian friends, and Happy Columbus Day to my friends in the US.

Before I get into our newest find in the bathroom plumbing saga, I will share some cuteness.

This is what the view out our bathroom window typically is, not that the platform has been set up for the winter.

The cats are just smashed together up there!

I think that’s Shop Towel with his head handing over the edge of the cat bed, being used as a bed by several kittens. He may be aggressive with the adults at times, but he’s good with the babies!

Nosy, I see, is cuddled up with him. Now that Nosy has been neutered, it does seem like he’s no longer involved in any aggressiveness that we still see at times.

Anyhow.

Today’s main job was to see if we could get a panel cut into the wall in my husband’s room, to access the plumbing for the tub and shower. After gathering what tools we thought we might need, my daughter flashed a light into the holes for the bathtub taps, to try and see where the wall joints were.

Turns out, they were pretty much right at the pipes.

Then she went to the other side of the wall, while I used the drill with an auger bit and made a couple of holes above the taps, trying to be close to the joists, but not too close, through to the other side of the wall. The first pair of holes was made using one of the narrowest auger bits. Once those were through and I got the go ahead from my daughter on the other side, I did them again, using a larger bit.

Then my daughter cut an opening in the paneling.

We hoped to be able to use the jig saw, but that would have hit the pipes. She ended up doing the first cut across the top, using the saw on her multi tool. It was the only saw small enough. After that, aside from having to start the first inch or so with the multi tool, she was able to use the pull saw.

My brother thought there might be aspenite behind the paneling, but there was no. It was just open joists. At one point, as my daughter was saying away, the panel was flexing so much, it made things almost impossible. I ended up reaching under her with a broom handle to hold it against the paneling to hold it, so she could finally finish the cut.

She wasn’t able to cut all of one side, though. She was a couple of inches short when she hit something. She pulled back the cut piece as much as she could to see, and thought there was a nail or something, in the joist. In the end, she cut everywhere else, then just snapped the panel off.

Finally, we could access the plumbing!

In the end, there was nothing we could do.

My daughter tried to take off the piece for the taps, but it just would not happen. It turned out it was soldered. I ended up taking pictures and sending them to my brother.

We took out the faucet set we have and discovered another problem.

It threads completely differently.

Here, you can see both old and new.

On the right, for the hot water, you can see that wood was gouged out of the joist to make room for the plumbing. There is also a strange pair of right angle beds in the hot water pipe below.

We don’t know why the cold water side is black.

In the middle, however, you can see the problem.

The old fixture is threaded internally.

The new fixture is threaded externally.

In the end, we put everything away, then taped the section of panel that was cut off back over the hole for now.

After a while, my brother was able to look at the photos I sent him, and we ended up talking on the phone.

It turns out that, 40 years ago, it was standard practice to solder plumbing together with lead. The only way we’re going to get that out is to cut it.

After talking about it some more, and getting a look at that bend in the hot water pipe, my brother suggested that we replace the copper pipe with Pex, including the pipe to the shower. We can then get Shark Bite parts and adapters to install the new fixture. The set we have includes a shower head, but we won’t be using that, since we currently have the accessible hand held shower (it has an extra long hose, and a shut off valve under the handle of the shower head).

I don’t know that I want to mess with the pipe for the shower, if I can avoid that. I have no idea how it’s attached at the top, and I don’t want to cut another hole in the paneling to see!

So that was it for today.

Tomorrow, I’ll be going to the hardware store. There’s a guy there that has been most helpful. I can show him the photos and talk to him about what we need. My older daughter says she can cover the cost, though at this point, we have no idea what those would be.

We did get a few other things done today, though it was nowhere near as productive as I would have liked. I have so much I need to do outside, and I’m just not getting to it!

My daughter and I got the last of the winter squash moved from the garage to the root cellar; we’re supposed to reach -3C/27F tonight, and I figured it was time. We did leave the big Crespo squash upstairs, though. It has the most damage to the shell, so we will see about using that as soon as we can. I definitely want to save seeds from this one, so we can grow them again next year.

The tomato paste I was making in the slow cooker out of just San Marzano tomatoes was finally done last night and left to cool until today. I like using the slow cooker for this, but it does take longer. I probably should have cooked it down more, but we were going to need the slow cooker. There was enough somewhat saucy paste to fill two 750ml jars. We’ll just keep those in the fridge to use as needed. We like to just add a spoonful of paste into various things, almost as a seasoning.

I did taste test it and, to be honest, I don’t find the flavour any better or worse than any other tomato sauce or paste we’ve made. I’ll have to get my daughters to try it. I’m not a good judge of such things! 😄

Our Thanksgiving turkey got deboned, and there is now a stock being made from the bones in the slow cooker. It’s as plain as plain can be. Just the bones and water. Not even salt, so that we can use it for the cats as well as for ourselves. We can add seasonings for ourselves, later.

The last of the vegetables that were under the turkey went into a pot, along with the leftover squash, some of the leftover turkey and some of the freshly jarred tomato paste to make a large soup. Between the soup and the rest of the turkey, we won’t need to take anything out of the freezer for a while!

We’re still having to heat water to wash ourselves and anything else, including the dishes. I have found that, if we leave the hot water alone long enough, we do actually get some almost hot water. It takes a long time for one element to heat up a 40 gallon tank.

Another job for tomorrow. Take the elements out of the previous tanks to see if any of them can be used to replace the burnt out one in our current tank. I took a quick look at one of the tanks while I was done there earlier today. The bottom panel is already open and I could see scale built up around the element on the outside.

There’s a reason we go through hot water tanks so quickly!

I’ll have to grab some tools and have at the old tanks. Aside from opening the panels and removing the elements to see how they are, I want to take out the anode rods. At the top of the tank is just a flat cap. There’s nothing to grip. I can’t see how it’s supposed to be removed without digging under it and scratching up the surface of the tank. Of course, nothing I find online is the same as what we’ve got. It’s probably a simple thing, but with how absolutely everything seems to be breaking at once right now… well, let’s just say I’m glad we’ve got a couple of old tanks to practice on!

Our new powered rod isn’t supposed to arrive until Oct. 22, so we have time for that. It’s the element that I really hope we can get replaced.

Meanwhile, the girls are going to be taking on scrubbing the area around the tub as much as they can before treating with with an anti-mold and mildew disinfectant again. Then, once that’s dry, all the exposed area will get painted with the mold and mildew resistant primer. Once that’s dry, we can look into getting the new tub surround ready to install. The most important part being, cutting the holes for the plumbing in the right places.

The tub itself is going to need a whole lot of CLR, too.

It’s going to be downright strange when all this is done, having a tub and surround that isn’t water stained with rust.

I just want to be able to have a real shower again, with water that wasn’t heated in a kettle, first!

Ah, well. Little by little, it’ll get done!

Very little, by very little, with this particular job!

The Re-Farmer