water well

We have water, and future plans

/ Re-Farmer / Leave a comment

My younger daughter and I started talking about what we wanted to do over the next while, both shorter and longer term. We got so into it, we ended up walking around the outer yard to talk about it more!

One of the stops we made was in the pump shack, where we tested out the old hand pump.

Much to my surprise, we soon had water flowing! I took video while my daughter started pumping. This confirms to me that all we need are new leathers for it to work properly. It shouldn’t take that long for water to start flowing again, once it had already started. It should stay primed and water should start flowing almost immediately.

Yes, the whole pump moves as the handle is pumped. It spins in place. I asked my brother about this, and he tells me this is because it is designed to basically float, allowing for the rise and fall of the water table. A neighbour of ours had the same system, but when they dug a new well and got indoor running water, they closed off the old well – I can’t remember how exactly that was done, but in the spring, when all the snow was melting and the water table rose, their pump ended up going through the roof of their pump shack!

After we ran water for a while, I even gave it a taste, and it tastes better than our household tap water. We really need to get our house well water tested, but we would need to do the full testing to find out what’s going on with it, which is out of our budget. Plus, once the samples are collected (full testing needs 2 samples in different sizes), we’d have to get it to a lab in the city within 24 hours. The sterile containers to collect the samples are, I believe, available in one of the larger towns in our municipality, but I’d have to confirm that. A fair amount of logistics is required for us to get the water tested, simply because of where we live. The full test, however, would include coliform, E. coli, HPC, Nitrogen-Nitrates and Nitrogen-Nitrites, total dissolved solids, calcium, magnesium, sodium, potassium, manganese, zinc, iron, Chloride sulfate, pH, hardness, conductivity, arsenic, boron, barium, fluoride, uranium, lead and copper – and the cost for all that has almost doubled since I first looked into it, 5 or so years ago. The basic test for just coliform and E. coli is just $30, but there are 7 different levels of testing available, including the total testing for everything.

Anyhow…

The important thing, though, is knowing we do have back up water, if something ever happens to our household water.

My daughter and I went through most of the old shacks and outbuildings, and into the barn, looking at the various materials strewn about. There are SO many old doors and windows, it’s mind boggling.

What started this all was my daughter asking what we needed before we could get some sheep or goats, and where we would set them up. We also talked about the trees that need harvesting, and the old shed with the collapsed roof that still needs to be dismantled. My daughter, it turns out, really dislikes working in the garden, doesn’t feel she’s good at it, and would much rather do other stuff. So for the next while, she’ll focus on harvesting and processing the dead trees and dismantling the old shed. The lumber from there can be used to build an animal shelter. The lumber used to frame it is still good, and the old cladding, which is very weathered and rotting, covers wider boards, protecting them enough that those should be useable, too.

I had originally thought we’d build our outdoor kitchen where the shed with the collapsed roof is, or right in front of it, but we now know that area is lower, collects water and the ground gets really soft. The other area I considered was next to the pump shack, facing the “driveway”. The old fuel tanks are still there, and we have no reason to move them. The outdoor kitchen is going to be 20’x20′, and those tanks would be in the way. There is, however, enough space behind the pump shack, between it and the old chicken coop. We just have to get it cleaned up of old tires and appliances still sitting there.

We also looked at the old chicken coop. This is a log building that still has its roof, though that is damaged. The original roof is wood shingled, and it had been covered with … tin? … corrugated sheets. I don’t think corrugated is the right word, but I don’t know what it’s actually called. Unfortunately, as with so many other areas, trees were allowed to grow right against the building. One had branches that scraped across the roof in the wind, which eventually tore off several of these metal sheets, destroying them and damaging the roof beneath, which now has holes in it, and the weather gets into the “attic” portion. We have other metal roof sheets like this that we can salvage from another collapsed shed by the barn, but have no way to safely get up there. We would need scaffolding, but the scaffolding my brother remembers being here is gone.

Still, we want to salvage this building. The log walls are still pretty solid. This building had been used as a summer kitchen, before my parents bought the property converted it to a chicken coop. It had electricity wired to it for lights, and heat lamps for the chicks. When my parents stopped having chickens, no one cleaned out the coop, so it’s quite a mess in there, and there are some things that were tossed in for storage, too.

We could potentially clean it up and fix it up. The whole building is slowly sinking. Instead of being on a concrete or rock foundation, it’s on giant wooden beams, and those are both sinking and rotting away, but they are also why the building is sinking evenly, and not twisting. The roof, however, is also dropping, to the point that the door had to be taken off entirely for us to be able to get in.

So that’s a project my daughter will work on as well; clearing up around the old chicken coop, first, then working inwards. Mostly, though, we have to cut back the trees some more – I’d already done some of that a few years back, but these are maples, so they’re growing back.

We’ll have to do the same around the pump shack, but one old stump has been sending out useable suckers. It’s basically been accidentally coppiced. We can maintain that. More material for wattle weaving! 😁 We also talked about what we can do to fix up the old pump shack. The exterior cladding it starting to rot and pieces are falling off – and on this building, there is no inner layer of boards the cladding is covering. It’s directly attached to the open wall joists, as you can see in the Instagram video. The concrete floor is cracking, but the bones of the structure are still sound, so we’ve got ideas on how to fix and maintain it.

We also went around the warehouse, which used to be my late brother’s workshop. We could seriously use that building for a workshop ourselves, but it’s completely full of my parent’s stuff. There’s basically two short paths among the stuff, and we can’t get to the back of it at all. My mother is still obsessed with her stuff in there, and is so worried someone will steal it. At the very least, though, we need to get the old mattresses to the dump, as well as the bags and bags of old clothing. She had suggested we have a garage sale, which I will not do, but she did approve of my suggestion that we could try selling things online, instead. That would be one way to help pay for the things that need to be done around here! That, however, would require going through all those boxes and seeing what is actually worth selling, and what is just junk.

But I digress!

It was around the warehouse that we decided on a place we could build animal shelters. My daughter is interested in sheep, for their wool (she wants to process and spin yarn). I would like a couple of milk goats, partly for their use in permaculture, partly because my family are lactose intolerant, and they can drink goats milk without getting sick.

We did talk about getting chickens, but both my daughters are hesitant about that. The problem is, they have friends with pet chickens, and their chickens are always getting sick. They think if we get chickens, they’ll get sick all the time, too, and we’re very unlikely to take a chicken to a vet. In a way, I understand this, but I think chickens raised outdoors would be much hardier and healthier than chickens raised as pets. Honestly, I’d be more concerned about sheep, goats or pigs needing vet care.

Yeah, I’d like a couple of pigs, too. Partly, all these animals animals are an important part of regenerative practices, and would go a long way in helping us to reclaim and improve our soil, with each contributing in different ways, and partly, they are a food source. Get a couple of piglets in the spring, send them out for processing in the fall, and have a freezer full of meat! I suppose we could get a steer and do the same thing, but I don’t think we’re up to an animal that big. Mostly, though, we need grazing animals for the outer yard. There’s no way we can mow all of it; it’s too rough in places. The overgrown areas are a fire hazard. A controlled burn would fix that, but with so many outbuildings, that would be very risky. Grazing animals would take care of that problem for us.

So my daughter is going to focus more on harvesting and processing the dead spruces for me to build raised beds, dismantle the shed and salvage materials to build animals shelters, as well as the outdoor kitchen and her smithy that she wants to build. I’ll focus more and gardening and building garden structures, and maintaining the yards. There will be crossover, of course, as we help each other out on the big stuff, but it’s clarified with each other what our areas of focus will be.

All in all, this made for a grand Mother’s Day! Well… except for all the wood ticks. We were picking those off our clothes constantly, and had to shower when we got back inside!

However, the three racks of ribs that have been slow roasting in the oven are now down, so it’s time to start focusing on our Mother’s Day dinner!

Mmmmmm….

The Re-Farmer

Bitter cold, and it’s the little things that are going to do us in!

/ Re-Farmer / Leave a comment

I am SO glad I was able to get the big shop done yesterday!

The temperatures were expected to go down over the next while, but still be just below average. Of course, the forecasts change constantly it still wasn’t by much.

Yeah, well… this is what we were at this morning.

Just in case the image isn’t loading for you, just after 8 this morning, we were at -31C/-24F, with a wind chill of -41C/-42F Our high of the day is still supposed to be -20C/-4F, which is actually our 30 year average low for the day, but the record low is -36C/-33F, so it’s still well within the norm. Will we actually warm up that much by this afternoon? I sure hope so, because we need to go into town! As it is, I cut my morning rounds down as much as I could, basically just making sure the outside cats had food and warm water, and that was pretty much is. I only counted 19 this morning. Most were in the sun room, but the ones outside were actually dancing around with their paws from the cold!

I’m really not looking forward to tomorrow morning. We have a vet appointment at 8:30 am, and it’s supposed to be about -28C/-18F at that time. Any wind chill on top of that will be brutal. We’ll be using the van for this trip because, for all the problems it has, it still handles the cold better than my mother’s car.

Speaking of handling problems, I finally got tired of one annoyance last night and did something about it.

I added string lights near my door.

This corner has the door to the old basement, and the door to my office/bedroom, and it is always really dark. It’s not too bad during the day but at night, even with string lights around the mirror hanging opposite my bedroom door, it is ridiculously dark. Usually, that results in tripping over or stepping on a cat at my door when I try to go in. Yesterday, it was an annoyance when I kept having to go into the old basement to check on things.

Also, those stairs really, really suck. And not just because my knees are shot.

The set of string lights I had on our Advent wreath got missed when the Christmas decorations were put away, so I added batteries and taped it around the basement door. It’s bright enough that I can now see the door handles, and even grey or black cats on the grey mat under my door (to protect the floor from their scratching).

As for why I kept having to go into the basement: noises.

Too many out of place noises.

Our well pump, every now and then, makes a vibrating noise when it starts. Of course, it stops by the time I get down to check it, and everything looks fine, but it really bothers me. At least it doesn’t make the grinding noise it used to. We have figured out that it would do that when too much water was being used at once, such as if the water for the shower was turned on too full. The pressure tank was being emptied faster than the pump could refill it, so it would start grinding. It means less water pressure while we are taking a shower, but that’s a small thing compared to burning out our pump and losing water completely. The vibrating noise is something else, though, and I can’t tell if it’s coming from the pump or the pipes to the tanks. Nothing has changed down there, though, so there is no obvious reason for it to start making that noise. It also seems to be a winter/cold weather thing, but I have no way to tell.

The pump has been going off more often, too. Even when no one is using the water, I would hear it start up. Some nights, I’ll be awakened because it’s turning on again. I’m the only one who can hear it, since my husband sleeps with a CPAP, which makes just enough noise to drown most things out, and the girls are on the second floor.

The problem is usually the toilet.

Ultimately, though, the source of the problem is our water. It is so full of iron and minerals, it’s messing things up. We’ll need to get a plumber in to fix the bathtub taps because the build up is getting so bad, the hot water tap leaks, even if only the cold water it turned on! When the plumber was here to clear the drain to the septic tank for us, he did take a quick look to give us an estimate, and he thinks he can fix it, rather than have to replace it, but we’d have to take off and replace the tub surround, since that’s the only way to access the taps.

It’s the toilet that is having more problems now. There must be quite a buildup inside the refill hose, as hardly any water flows through it, and it’s taking longer and longer for the tank to refill. The entire inside, which is lined with Styrofoam insulation, is coated with iron, which is also interfering with the flap. Sometimes, after flushing, the flap doesn’t seal right, so the tank keeps draining about as fast as the water is flowing to refill it, so the tank simply doesn’t fill. Unless someone happens to use the bathroom soon after and notices it – because there isn’t enough water to flush! – it’ll keep going for hours. Which is how I end up being awakened by the well pump going off repeatedly during the night! All that needs to be done is to give the lever a wiggle; the flap will settle in place and the tank will finally start filling. Looking at the parts and pieces, though, what I’d really like to do is simply replace all the innards. It’s all so coated with iron and minerals, that would probably be the best way to not just solve a couple of small problems, but keep them from happening again for a long time.

Which leads me to another little problem we’ve been having, thanks to our water quality.

The bathroom sink.

This still has the original tap and faucet set, from the mid 70’s or so. When the water flow starts to get bad, we usually just unscrew a piece from the faucet, give the parts a scrub, then put it back. If it’s really bad, we’ll soak the pieces in CLR for a while. The problem just kept coming back faster in between cleanings, though, and getting worse.

Last night, I had the pieces soaking in CLR again, but when I put them back, the flow was even worse than before the soak and scrub. I gave it some extra scrubbing, but that made things worse again, not better. I tried clearing the openings more directly but, again, it just got worse. When I put it back in place and almost no water could go through anymore, I had to do something more drastic! I took the part in question (I don’t know what it’s called) over to my craft table and tried to clear the holes with a pin. Which worked on one side, but not the other.

After much fighting with it, I managed to separate the pieces.

The grey piece at the top of the picture wasn’t too hard to clean. Especially when I was eventually able to get out the two other pieces inside. It was all so full of rust and gunk, each layer needed to be cleaned before I could get the next one out. The openings are large enough, the T pin I was using had no problem clearing them of scale and rust.

The real problem was the green piece.

The conical part you can see, with the fine mesh of holes, was still clogged. The holes on the bottom are even smaller, much fewer, and barely visible. I cleared them with a pin as best I could, but it was just not working well.

Eventually, I did get it to the point that the conical part started spinning around. Only then could I figure out where the pieces came apart. After much fussing – and the use of a tiny screwdriver – I was finally able to pop the conical part off.

Well, no wonder we were having problems!

Note that this is AFTER multiple soaks in CLR.

After wiping them down, I set the conical part aside to soak in CLR again, while I used the pin to clear the holes in the other part – holes that are much larger on the inside than the outside! Eventually, I got it to the point that I could see through all the holes when I held it up to the light. Not all the holes you see in the photo go all the way through. There’s just the circle of holes around the outer edge, plus another circle of holes half way to the centre.

Then I took the pin and cleared every last hole in the conical part.

By the time I was done and everything was put back together, it was 2am.

One of my daughters happened to be using the bathroom, so she put the newly cleaned part back together with the other parts and screwed it all back into the faucet for me.

Then we stood there and watched in awe over how much water was flowing through, as we let it run to make sure there was no CLR residue left. It hasn’t flowed this well in decades!

Now, if we could just get the toilet tank parts to flow as well!

At least this was a small thing we could take care of ourselves. There’s another new thing that is stressing me out.

The furnace has started making noises.

Of course, with this cold, the furnace is turning on more often, and staying on longer. This house is not very efficient, either, so we lose heat quickly. For all the time the furnace is on, the upstairs is still very cold. There’s only one heat vent for the entire second floor, and the girls have not noticed any real difference since the roof was done. Ah, well. It would have been nice!

Last night, I kept hearing the furnace turn on and start making a strange vibrating noise which – like the well pump – would stop by the time I hobbled my way down the basement stairs to check it.

I ended up turning the thermostat down, so at least the furnace would turn on less frequently, and not stay running as along. Oddly, after I did that, the vibrating noise seems to have stopped completely! Which doesn’t make any sense at all.

What we need to do is get someone to come in and give it a check, and do any maintenance stuff it needs. The problem is, we need to set aside funds for a replacement vehicle. Funds that would normally cover the cost of such irregular expenses. It becomes a battle of priorities over the dwindling “unallocated funds” part of our budget, since rising costs for everything else keeps chipping away at that, too.

It’s all these little things that are going to do us in. The well pump. The septic. The furnace. The taps. The toilet. The lights. The outlets. etc. All these accumulative things. Yes, it’s an old house. This sort of thing must be expected. Especially since there’s very little of this that we can do ourselves, and our resources are so limited.

So we try to focus on the stuff we do have control over, and juggle the budget to find ways to pay people to come in for the stuff we don’t.

The crazy thing is, a significant portion of these problems are caused by our water. It’s simply to loaded with iron and minerals. What I’d like to do is add a filter to the line going into the well pump. A simple filter would extend the life of all sorts of things! There are types that can be cleared without having to open it up to change filters, which would require re-priming the pump. Adding a filter is not going to be done until the pump is replaced, and we’ve already had three plumbers not want to do that (my brother already bought a new pump and all the fittings) due to the risk of the foot valve, at the bottom of the well, disintegrating and losing our water completely. That would turn a job of a few hundred dollars into a job of several thousand dollars, because of the set up we have, and the lack of availability of parts we would need. The valve itself is cheap. It’s all the other stuff that would have to be done to get to it that gets expensive!

Yup. It’s all those little things. They sure do add up!

The Re-Farmer

We have a second well… sort of

/ Re-Farmer / Leave a comment

Today, I finally had a chance to move my dad’s old welder aside, so I could access and test the well in the old pump shack.

Do I want to know why there is apart of a toilet seat there?

No. No, I do not.

I moved a few more things around, then set the old cream can under the pump’s spout, just in case I actually got water flowing.

I took an accidental picture while pumping the handle. I thought it looked very dramatic, so I kept it! 😀

We got water!!!

Sort of.

This well was here before my parents bought the property, and it is a design that does not need to be primed. After much pumping, I was able to get water flowing, but if I so much as slowed down, the water would stop and I would have to start pumping hard, all over again. Which meant I wasn’t able to get a photo of actual water flowing from the spout. 😀

On the one hand, this is very encouraging. If something ever happened to our well, we will still have access to water. We should get the water flowing more to clear it out a bit, and then just get it going regularly. There is a problem, though, and you can see part of it in the above photo.

The pump is not fixed. It’s just sitting on top of the pipe. It actually rotated while I was pumping!!

When I was a kid, we had a different pump completely. It had a sort of frame around it, supporting the mechanical pump mechanism, which was run with electricity. If the power went out, we could attach a handle and pump it manually.

I don’t know when or why the old pump was removed, and I am flabbergasted that this manual pump was hooked up, without some sort of base to attach it to, so it won’t move.

My brother tells me there are repairs to the well pipe needed. I suspect that getting that done would result in it becoming much easier to pump water.

It would be worth getting that done. I would also like to set up the electric/manual system we had before, too. We still have the attachment for the spout of the pump that we used to divert water out a hole in the wall, to a water trough for the cattle outside.

Being able to use electricity to pump the water would make life easier in general, but if I had to choose only one, I would go with a manual pump over electric, as this would be a back up source of water should we ever lose power.

The Re-Farmer

Encouraged

/ Re-Farmer / 8 Comments

Well, after getting such bad news from the plumbers, and passing on what they told me to my brother, he gave me a call, and I’m feeling much more encouraged.

There is no one alive today that knows this farm and the systems that run it better than my brother. So when I told him in more detail about what the plumbers had said, he was torn between disbelief and laughter, that they would be so unfamiliar with, and intimidated by, the system we have. It’s still used a fair bit, and he had no problems finding a replacement for the basement pump.

He does not share their concerns about the immersion pump and that we might lose our water. This pump has been replaced about 4 times in the past 50 years, by his memory, and it has always been a relatively simple switch.

He will be coming out to do it himself. He just has to find the time in his own schedule to make the trip out. It was something we both hoped to avoid, but he’s frustrated by plumbers that are so intimidated by our old system.

By the end of the call, I was feeling much more encouraged. As much as I am willing to trust the professionals, my brother knows things about our system that they don’t. If he is confident that the pump can be switched out without causing problems in the well itself, I trust his experience.

Speaking of wells, I remembered to ask him if he remembered what happened to our old well, from before this one was dug. This pump was operated with electricity, but when we had power failures, we could attach a handle and pump it manually. I remember bits and pieces of when problems started, but not why. He told me that the water had started to come out dirty. His guess is that something collapsed in the pipes. I then got the lowdown on how that well was set up, including that it has a piston at the very bottom, some 80 feet down. So when it was first being pumped, it would take a while for the water to reach the top (I remember that time it took before water started to come out). Of course, once it was no longer being used for a long enough time, that water would slowly drain down again.

Theoretically, if I pumped long enough, I should be able to get water out of them, but it is most likely the pipes need to be replaced.

That opens up possibilities for us, since one of the things we want is to have a manual pump well as a back up if we ever lose power and can no longer get water from the well by the house.

I wonder if I should move things away from that pump and give it a try?

The Re-Farmer

Can I just quit now?

/ Re-Farmer / 5 Comments

Honestly. I would really like to just quit right now.

This morning, I tried calling a plumber about switching out our well pump in the basement. This would be the third plumber we’ve contacted in the past few weeks.

To recap: we are on a deep well for water. There is an immersion pump in the well itself, and two pipes going from the well to our basement, into another pump. The two pipes in at one end become one pipe out the other, pumping water into our pressure tank.

The well pump in the basement has been making noises. At times, the pressure is lost, as if it is losing prime, or as if we’re using the water faster than it can refill the pressure tank. When that happens, it makes a grinding noise. Once the pressure gauge on the pump is where it’s supposed to be, it goes quiet and stays quite for the rest of the time it’s running, but the noises return frequently, if not every time it turns on. Basically, it seems to be wearing out.

My older brother had bought us a new pump and was going to install it for us, but we ended up fighting with our septic, instead. So the new pump, with all the fittings, clamps and whatnot that he could think of possibly needing, has been sitting and waiting ever since. Instead of making my brother come back, we were just going to hire a plumber. Unfortunately, the “discretionary” funds had to go towards vehicle repairs, but I really wanted to get that done before winter, in case the plumber needed to go into the well, since there was also the possibility the foot valve in there was leaking.

I called the plumber and left a message, honestly not expecting to hear back until Monday. So it was a pleasant surprise to get a call back a couple of hours later.

I had said in the message what we needed done, and that we already had a pump. It just needed to be switched up.

When he called, he asked if I meant the immersion pump. No, I said. The one in the basement. He seemed confused. I brought up the possibility of the foot valve leaking in the well, but that it was the pump in the basement that was making the noise, and we wanted to switch that out.

He said they had better come out and take a look.

They came out this afternoon!

I now understand why he was confused. I’m starting to get the impression that we are the only ones that still have this old system. Once they were in the basement, checking it out, he explained that basically, no one likes to work on these systems, because they are such a problem. He asked me to turn on a tap to trigger the pump to turn on, so I went to the bathtub and did what we normally avoid doing: turned both taps on to full. This not only turned on the pump, but triggered that grinding noise and, eventually, I lost water to the tub. Which is when I shut off the taps and joined them in the basement again.

Once the pump’s pressure reached where it was supposed to be, the pump was nice and quiet again. He told me that, it’s not a matter of simply switching pumps. The front cap of the new pump would have to be removed and installed inside the well itself – and there would be just one pipe leading to the basement and the rest of the pump. There was a good chance changing it would cause further problems, which is when he asked to see the well.

They were able to get the cap off, with it’s one bent up handle. I am pretty sure this is the first time I have ever seen the inside. My only memories are of when the trench was dug from where this well was dug, towards the barn. That is where a water pipe to serve the barn and water fountains for the cows was laid, as well as the main pipe for the grey water from our septic tank. I don’t know exactly where near the barn these pipes split off in opposite directions, but I do have a general idea of where it must be.

Once the plumber used the ladder to get into the well, his assistant had to take it out so he’d have room to actually move around.

The news did not get any better.

It seems ours is a 4 inch well. Modern wells are 5 inch. That means there is a smaller immersion pump – a size that’s very hard to find these days.

Like the first plumber we talked to – the guy who has worked in our well before – he said it would be better to replace the immersion pump. This would mean one pipe into the house (the other could be used for the electrical wires to go through) and no pump in the house.

The other problem with doing that job is, the cap inside the well – what he was standing on to check out the system – would have to be removed. There’s no way to know how high the water table is right there, but given how damp and rusty things were, it’s probably quite high. Which means they’d be working in water.

However, this is a 50 year old well.

What we really need is a new well.

We could do all the other work, spending what might be as much as a couple thousand dollars but, in the end, we could lose out water entirely. He did not dare even switch out the pump in the basement, for fear of losing us our water.

As we were chatting, I asked questions and mentioned various things, ranging from the snails that showed up in our fish tank after using well water to make a change (I forgot to mention the algae blooms), and how we stopped drinking the water since them,to having to shock the hot water tank with hydrogen peroxide regularly because of the smell.

By the time I got to that, he was looking a little wild eyed. What had been, to paraphrase, as sort of “I won’t go so far as to recommend it, but if it were me, I’d drill a new well,” became a “yeah… you really need a new well!” The more he heard about it, the more he wanted to stay away from doing things like replacing the pumps, either one at a time, or both at once. We definitely have issues that are beyond what they can do for us.

In the end, after apologizing for being the bearer of bad news, I gave him my email so he could send me some names for well drillers.

Oh, and when I asked if he knew what a new well might cost? Depending on various factors, of course, it could cost as much as $10,000.

I told him that if we had that kind of money, we’d have a new roof! 😀

Normally, they would have charged for a service call like this, but by the end of it, he said he would not charge us anything. Then apologized again for all the bad news. My response was along the lines of, with this place, I’ve come to expect it!

For now, we were basically told to hang in there with what we’ve got. We have water right now, and it’s not worth jeopardizing that until we are in a position to get the job done fully.

So, not only do we need $10,000 for a new roof, now we need another $10,000 (estimated) for a new well. That’s on top of everything else that needs replacing, like flooring and walls and repairing the old basement walls, and the weeping tile under the new basement… on and on it goes.

Coming up with that kind of money is a challenge all on its own. Doing it without jeopardizing my husband’s disability insurance is another issue. If we made that much in “income,” he’d basically lose his insurance. It’s not just a matter of his disability income that we are living on, but coverage for his medications.

Needless to say, I got zero work on the sun room door today.

It would be so much easier if we could quit, somehow.

But that’s just not an option.

So, I guess we’ll just have to figure something out.

:-/

The Re-Farmer