Must start with the cuteness!
I spotted Adam nursing this brood in front of the sun room – and I needed to get past her! I had to go back and forth from the sun room a few times, and saw her nursing in the same spot again, but with different kittens!
She is such a good creche mama. So chill with the babies!
Not with people, though. She still won’t let us near her, and ran off when I got too close. Unfortunately, she seems to choose high traffic areas to lay down and nurse!
Meanwhile, I got a bit more progress done on the cat isolation shelter.
As I mentioned in my last post, I changed the plans a bit. The original plan was to basically have a cube with the outside frame divided into quarters, vertically and horizontally. I had it in my mind to attach the vertical pieces first, like wall joists, then horizontal pieces to support the floor boards in the second level. The problem was, how to attach the shorter horizontal pieces, with the materials I had on hand. There are brackets and braces that can be used to make the job easy and secure, but I don’t have any, and don’t have the budget to get them.
Then it occurred to me that this shelter doesn’t need vertical support. The true to size 2x4s are strong enough on their own. I’ll still add them, as they will help hold the welded wire mesh, but it’s the horizontal pieces that are more important, since they will be supporting the floor boards.
So the longer regular size 2×4’s I cut will now be mounted horizontally instead of vertically – they will be doing inside the 4′ square front and back frames, so the measurement doesn’t change. I needed two more for the shorter sides, which meant I needed to more pieces the same length as the pieces that will be the top and bottom.
In the first photo of the Instagram slide show, you can see the two new pieces that were cut. The others, meanwhile, were flipped and ready to get their other sides painted.
The rough cut true to size 2x4s sure use up a lot more paint compared to the smooth regular size 2x4s!
I still had the problem of how to attached them to the front and back frame pieces. They will be butted up against the edges. I decided to cut pieces at 45° angles that will be butted into the corners to give me something to screw into. These will be needed for the top and middle pieces of one side. I’ll need 4 more of these for the other side. I used leftover scrap pieces of true to size 2×4 I do have a short length of that left. I’ll see how these work out before cutting more. I might decide to do it a different way. Or just cut them a bit longer. That was my original intention, but the pieces I had left over weren’t long enough.
Hmmm… now that I think about it, I can use longer pieces to support the top corners of the frame, and these shorter ones to support the horizontal pieces in the middle of the frame. I’ll have to think about that some more.
I did have an issue making the 45° cuts. I’m using the miter saw I picked up at a garage sale a couple of years ago. Today is the first time I needed to make angled cuts.
I don’t know how long its been since this thing was used for angle cuts, but it had to be a long time! I had to get lubricant to get it to turn all the way, from one side to the other! But, I got it done, and am soooo happy I have this saw! Previously, I used a hand saw and miter box to make cuts like this, and that really sucks. Especially with wood as hard as this! My soil sifter’s frame would have turned out much better if I’d had this when I made it. 😄
At this point, there isn’t much more I can do until all the painting is done. Once I have the outside frame assembled, I can take the measurements I need for the cross piece that will go through the middle to support the floor, and for the vertical pieces. I’m not working with two different sizes of wood, so I don’t want to count on just doing the math.
I’m not that good at math!
After cutting the 45° angles, I was left with a bunch of equally sized triangles that I’m hanging on to; they might come in handy, later. I should have had 8 of those, but one of them fell apart, because the end of the 2×4 I was cutting off was one of the more damaged pieces.
The painting, unfortunately, is going to take a while, since it basically needs a whole day to cure. It wouldn’t normally take that long, but it’s humid enough to slow things done and keep things very tacky! About the only other thing I can do in between flipping and painting the boards is cut and start painting four more angled pieces.
Still, progress is progress, and I’m happy with how it’s going so far.
The Re-Farmer
The Re-Farmer 
Pingback: Our 2024 Garden: first garlic, plus winter squash, melon and pumpkin progress | The Re-Farmer