Today, after many, many delays, we finally got some progress on those raised bed covers we need to build!

My daughter and I set up the folding table we made using the legs we found when cleaning up the new basement, and a section of 3/4 plywood found in the pump shack. The hard part was finding level enough ground for it, and still be close to the outside outlet. We ended up putting it almost against the house, and that’s where we set up the miter saw. Then we moved the swing bench that’s been sitting on the sidewalk block patio under the kitchen window for the past while, so we could set up the table saw close enough to plug it in without an extension cord.

The first thing we tried to do was cut the 12ft long 1″x4″ boards in half, lengthwise. My daughter, sweetheart that she is, found where the saw blade could be adjusted up and down. My husband and I had tried everything to raise that blade and finally concluded it couldn’t be raised. Turns out, it was just badly rusted and that’s why it wasn’t moving. !! I wonder how many years it sat in that shed before I found it?

The first two boards we cut in half did not go well! My daughter was feeding the board from one side while I supported it from the other, but it just did not want to stay against the guide. We ended up with some wobbly cuts! So we cut the others shorter first, then cut them in half. We measured the beds first to confirm the dimensions. The side boards total 9′ long, but then there’s the width of the end boards; I forgot I’d attached those to the ends of the side boards, and not to the insides. That made the beds 9′ 2″ long. The end boards were 3′ 1/4″ long.

So we will be cutting 9′ and 3′ for the cover frames.

The boards were exactly 12′ and 1/4″ long, so we just measured off the 9′ and cut it. The cuts take off a fraction of an inch, so the remaining sections should be almost exactly the right length for the short ends.

It was much, much easier to cut the shorter lengths in half on the table saw!

All the pieces are now cut. The 3′ lengths are in the front, then the 9′ lengths. In the back is one of the two first 12′ boards we cut in half, with the wonky cuts. The other one was used to cut more 3′ lengths, since being a bit wonky won’t be an issue for some parts of the build.

There is also one board at the top of the photo that was set aside because it has damage on it in two places. We will still be able to use the undamaged parts at some point.

As for the plans, I sketched what I had in mind out for my daughter.

We will be building four 9’x3′ frames, but two of them will be used in one cover. The Tom Thumb corn is going to need taller protection from deer, so two frames will be joined by 3′ vertical supports. One more support will be added across the top in the middle, to keep it from bowing outwards. I also plan to add screw eyes inside the middles and tie a cord across, to keep the sides from bowing out. A cord that close to ground level will be less in the way of growing plants.

At this point, we could just put a net around it, though if we wanted this over a bed with taller plants in it, we could potentially add hoops to the top for extra height.

That box frame is the one we need to get done first, as the corn is most at risk for getting eaten. Between the deer and the racoons, it’s going to become an issue in the near future! If we want to keep racoons out, though, we’ll have to use hardware cloth and find a way to secure the cover to the frame, so they don’t just knock it off.

The other two frames will have rounded tops. We have some wire fencing with 4″ squares that I plan to use with one of them, making a slightly higher cover. The fence wire can then support things like netting, plastic or shade cloth, as needed.

With the other, I was thinking of using the hoops that are currently still over the carrot bed, but… now that I’m looking at the plans, I realized we have enough of that wire fencing to use on both frames. We could make them different heights, for different needs. A shorter one, for example, would be handy for shorter produce, or to create a mini greenhouse over newly sown beds. A taller one would be great for plants that grow higher, but not high enough to need that box cover we’ll be putting over the corn.

As we build more high raised beds, the plan is to stick to the 9’x3′ size, so that these covers can be used interchangeably on any of them. We’re doing three covers for now. One of them should be useable on the high raised bed we have now, which currently has hoops to protect the beans from the deer. The box bed with the red onions does not really need a cover, except maybe to keep the cats from lying in it, or the birds from digging in the mulch. Over time, we plan to build enough covers for all the raised beds we make.

As for cutting the pieces, I was really happy. We will definitely need to get a new table saw, as this one was having issues. It will do for now, though. What I was really excited about was the miter saw. I bought it at a garage sale, and this is the first time we’ve tried to use it. Of course, it didn’t come with an instruction manual! Which is fine. It’s easy enough to figure out.

Up until now, I’ve been using a hand saw to make cross cuts. No matter how careful I am, I always end up making crooked cuts, and there are always those little bits of wood that break before the saw can cut them that need to be sanded. So excited to get beautiful clean cuts! Plus, the speed of it was fabulous!

Once the cutting was done, I realized we would not have enough screws to assemble them all, so we decided to go into town and get more. The table and miter saws got put back into the sun room, and the cut pieces went onto the table we used for the miter saw. We were getting hints of rain, and we didn’t want to take a chance. It’s a good thing we did, because there was a downpour while we were out!

When we got to the hardware store, we drove around the block a couple of times but could find no parking, so my daughter offered to buy us lunch! By the time we were done, things were no longer so busy, and I was able to park and run in.

Before we left home, I took a pair of calipers to the water pipe leading from the house to the garden that needs to be repaired. It’s a 1 inch pipe. After finding the screws we needed at the hardware store, I went looking for a flexible PVC coupling with metal clamps. The smallest size they had was 1 3/4″. That would leave too big of a gap for the clamps to be able to seal it on a 1 inch pipe. I talked to an employee, and showed her the picture I took of the calipers on the water pipe, which also showed the crack in the pipe very clearly. She tried to find something else that would work, but there wasn’t anything they had. In the end, she recommended I talk to a plumber.

What I will most likely do is go to the hardware store in my mother’s town, which is where I first had the flexible coupling recommended as a possible fix. They are a bigger store with a larger plumbing section, and may have a smaller size coupling in stock. If worse comes to worse, we can order them online. In fact, I’ve already found some sized specifically to fit on 1″ pipe.

As you can tell, I’m really hoping to avoid having to dig up and replace the entire length of pipe!

By the time we got home, the downpour my other daughter told us about was done! I don’t know if it’ll be dry enough for us to start assembling the first cover today. We’re supposed to get more rain, too.

This is where I really wish the storage shed wasn’t full of my parents’ stuff, that my mother insists we keep and is constantly afraid someone might come in and steal. As if anyone would be interested in the bags and bags of their old clothes, boxes and boxes of household stuff, or their old furniture. My late brother had used that building as a workshop, but that was more than 10 years ago. We never had a chance to even see what all was still in there, as my brother and his wife had already started moving my parent’s things into there before we moved in, and it was being used as storage for other things even before then.

So we make do with working outside, when the weather allows!

Well, this project has been delayed repeated for about a month now. One more day won’t hurt, if it comes to that!

The Re-Farmer