Since I ended up driving around again today, once I was home to stay, I took advantage of the cooler temperatures and calmer winds to work on the trellis bed.

View this post on Instagram

A post shared by The Re-Farmer (@the.refarmer)

One larger base log was ready. The next step was to use a garden fork to loosen the soil from one marker to the other. Aside from pulling out as many weeds and roots as I could, I was also able to use a hoe to try and adjust the soil height. The log is, of course, wider at the base, plus the ground has a slight dip at one end, so I brought loosened soil from one end to the other, to try and make it to the log would be more or less level once on the ground. Plus, with the loosened soil, it wasn’t going to roll around out of position on me. Once that was on place, I could start debarking the log that would be set on top of it.

Debarking is pretty fast. It’s all those branch bits and lumps that slow things down!

View this post on Instagram

A post shared by The Re-Farmer (@the.refarmer)

After doing the top half, it started to get pretty painful on the back, so I used one of the poplar logs that will be vertical posts to raise the end. It worked for helping the back, but the saw horse kept rocking, and the poplar log kept wanting to roll! 😂

Once the smaller log was debarked, I use the baby chainsaw (electric pruner) to sort of flatten the base log from end to end. Mostly to get rid of some lumps where branches used to be. The smaller log was naturally flat next to a couple of branch stumps, so I took advantage of that and flattened the rest of the lot a tiny bit, to match the naturally flat part. It’s not a perfect fit, but I wasn’t really trying for one. I might level things off a bit more, but if I do, it’ll be when I have the chain saw set up, so I’m not killing the batteries on my mini chainsaw so quickly.

Next, it was time to work on the large log that will be the base log for the other wall of the raised bed. It had more branch bits to cut off than the other two, but once those were trimmed, debarking went quickly.

At that point, it was time to stop for the day – and for the draw knife to get a good cleaning and sharpening!

I expect to actually be home all day tomorrow, so I’ll be able to finally make more tomato sauce. When I get back to working on the bed, I plan to make use of the pieces of rebar I’d picked up for the shelter we could never get set up. I’ve got auger drill bits in that size. Once I’m satisfied with out the side logs are resting on each other, I will drill a pair of holes, then hammer in the rebar, so hold the logs together. When the time comes, the ends will be joined with 4′ logs, but first the ends of the side logs will have to be trimmed even. That will be much easier if I can do that while they are already secured into position.

As for the vertical supports, I am changing my mind on how to do those, again. I’d been planning to set the posts inside the raised bed, before they were filled. Setting them in the middle of the beds would result in a trellis tunnel that is 6′ apart across the top, and would give access to both sides of the bed for planting and weeding.

The more I think about it, though, the more potential problems I can see with doing it that way. Primarily, I’d have to treat the bottoms of the posts to prevent rotting. I was planning to debark and char them. With the winds we’ve been having, though, the chances of being able to get a fire going to do that don’t seem pretty good. Also, finding straight horizontal pieces that are 6′ long is going to be harder. I have enough vertical supports to have 4 posts for each of what will be 4 beds like this. I could try to harvest more poplar to have more verticals, but finding nice straight ones in the right size has not been as easy as I thought it would be, and I don’t want to be wasting trees. So if we have 4 verticals per bed, they would need to be 6′ apart, and I would need three 6′ pieces per bed – or 12 in total, for the 4 beds we plan to build here. If the trellis tunnel sides are also 6′ apart, that adds another four 6′ pieces needed per tunnel, making 20 horizontals in total.

Now I’m thinking I should attach the vertical supports to the outside of the beds, along each side of the tunnel space. I can see a few advantages to this.

First, I won’t have to dig any post holes.

Second, if they are attached to the outside of the beds, they won’t be buried in soil and I won’t need to treat them to keep them from rotting.

It will also be easier to find shorter, straight pieces for the horizontals, plus it will be easier to reach and work on the tops to attach them. Right now, I’m just aiming to do one low raised bed with a trellis wall. Even if we manage to get the second half done, the horizontals at the top don’t need to be until later. Plus, it will be much easier to attach 4′ lengths onto the verticals later on, than 6′ lengths with half a garden bed to work around.

By not having the verticals in the middle of the beds, they won’t take up growing space. Also, these beds are 18′ long, and 4′ wide on the outside. Our raised bed covers are intended to be interchangeable, at 9’x3′. Without the verticals inside the bed, we’ll be able to fit a pair of them over one 18′ bed, if needed. The logs are wide enough that the actual growing space will be closer to 3′, so the covers will have frame support.

The main reason I wanted to put them down the middle of the bed was to be able to reach the growing space from both sides. It had been my intention to reuse the hardware cloth and chicken wire from the old squash tunnel for this. However, as long as we use something with large enough openings, we’d still be able to tend the bed, through the trellis, just like we’ve been able to do with the cover currently on the high raised bed, made with the stronger fence wire and larger openings.

The one real drawback is now to secure the verticals to the walls. I might still have to dig post holes.

I’ll figure that out, when the time comes.

In other things…

I did the running around I had to do; since I had to go to Staples to get the printer ink we needed, and it shares a parking lot with a Walmart, I took advantage of that and picked up a few things, including more of the shredded cat food the cats in the isolation ward prefer. Or maybe it’s me that really prefers it. It’s much easier to divide into bowls than paté.

Once we had the printer ink, we could print off the label we needed (frustrating to have to buy colour ink to print something that is black and white text!), then pack up the RAM that didn’t work with my husband’s computer and drive to a Purolator depot.

There is one thing that’s new right now.

When feeding the cats outside for the evening, I was able to catch a little black kitten.

I brought it inside.

It’s just the tiniest little soot sprite!

My younger daughter has always wanted an all black cat. Now, she will have one.

So far, it is not too keen on this whole “indoors” thing, and being surrounded by strange kittens. It doesn’t even seem to recognizes its brother. However, it quite enjoyed its first taste of wet cat food! I can hear it wandering around behind me, sometimes giving out a strange, hoarse little meow.

It will take time, but Pom Pom is starting to warm up to attention now, and hopefully that will encourage Sprite to accept attention from humans, too. If things go well, I hope to have it well socialized by the time my daughter gets back from house sitting. 😊

The Re-Farmer