Today, I needed to drive my mother to her doctor’s appointment, but didn’t have to leave until morning.
That gave me a chance to check on our emergency diverter set up that my brother made outside the house, ensuring that things were still sitting where they needed to.
Aside from making sure the PVC pipe my brother found was snug against the house, this is the important part.
The orange tarp partially buried in snow is the end of the insulated tarp covering the septic tank that we did not have to move. It was pulled away from the house, instead. This end gets frozen harder to the ground.
The two lengths of pipe need to be kept straight and slow downwards. At the bottom left corner of the above photo, you can just see the section of chimney flu that is supporting it closer to the house. We used basically what we could find in the dark. They will do the job, as long as things stay where they are supposed to. The shoveled area in the snow will basically become a skating rink.
In the distance, you can see the large flexible hose that was meant to be used. The problem is, it doesn’t straighten out entirely. Ever snake-like turn is an area that water could potentially slow down and freeze. The pipe is about 6″ in diameter, but even that can eventually fill and freeze solid. So it looks like we won’t be able to use it.
But I’m getting ahead of myself.
Using my brother’s car (and making sure to give the engine time to warm up, first!), I headed out early enough to hit the post office.
Alas, the mail that I’m expecting that didn’t come in due to the postal strike, still has not come in. Nor has anything else. Not even junk mail. The strikers may have been ordered to return to work (as a Crown corporation, the Federal government has the authority to do that), but apparently, that doesn’t mean they are going to actually do their work.
Oh, something I learned about this strike. It turns out that Canada Post has two unions. One is for the regular postal workers we see delivering our mail and in the physical buildings, like in our little hamlet. The other is for the ones that work in the distribution centres and such. Those are the ones that went on strike. So, while regular postal workers still showed up for work, they couldn’t do anything, because the distribution centres were shut down. It was a rotating strike, so every week, a different distribution centre would be active again, allowing for some mail to trickle through. Of course, if it was going from one distribution centre to the next, that really didn’t make much difference.
But I digress.
From there, it was off to my mother’s town and, since I was so early, I swung by the hardware store. After talking to one of the staff, I picked up some reflective insulation. They sell this stuff in sizes large enough to wrap around hot water tanks, to narrow strips that would be wrapped around pipes. Which is exactly what I wanted. I also got a small roll of aluminum tape. I plan to wrap the outflow pipe where it butts up against the house, as that is the area most at risk of freezing. Then I plan to add some between the pipes and the supports. Where the log is, isn’t much of a concern, but the ceramic chimney flu and the brick can both chill the pipe and potentially cause an ice build up on the inside. Just a bit of insulation would prevent that.
From there, I made a stop at the gas station. I didn’t need gas yet, but I knew my mother would be getting her Meals on Wheels today. Though I had a large and late breakfast before I left, she had told me she didn’t like to be eating by herself, with someone watching her. So I picked up some of the potato wedges she likes so much, so that I could snack while she was eating, and she could have the rest with her supper, later on.
When I got to her place, though, she had just finished eating her main meal. So we had some tea while she ate her desert. 😊 We were able to have a bit of a visit before we had to leave, and I updated her a bit on what was going on, and that my brother had lent us their car rather than my SIL driving all the way out to drive both of us around, and that he’d installed the diverter. I’m not sure, but I think she was still living at the farm the last time (and first time) it was used.
We left early to go to her doctor’s appointment, and I’m glad we did. I ended up having to go back to her apartment to get her little folding foot stool. Even though the car is so much lower than the truck, she still needed the stool to be able to get in! That is a definite drop in mobility.
Once at the clinic, we had a long wait, as everyone was being called in late. Once in the examination room, we still had a bit of a wait. When the doctor finally came in, she started off asking if we could move to another room, but then she saw my mother and told us to stay put, she would go get her laptop. It turns out the clinic was having network problems with all the examination room computers, and that was why everything was behind.
So we tried to keep it short. The main thing was to get my mother rescheduled for the MRI we didn’t get to, due to dangerous road conditions. I confirmed that my mother’s file was up to date about her macular degeneration and treatment. The doctor has nothing to do with this, as my mother is being treated at the eye clinic in the city, but as the primary doctor, she is supposed to have all this information sent to her. Then we talked about my mother’s breathing issues. One of her neighbours has asthma and uses a puffer (inhaler), so my mother decided she should have one, too. So could she be tested for asthma?
The doctor just prescribed her a puffer. She explained that she could recommend her for testing, but that is done in the city, and my mother would be on a waiting list for probably a year. Using a puffer won’t hurt her. I don’t think my mother as asthma, but even if there’s just a placebo effect, it would be worth it.
After giving my mother a basic physical exam, the doctor adjusted one of her dosages, and that was it. We knew the doctor was behind because of the computer issues, so we didn’t talk about much else. Which is good, because my mother usually wastes time by asking personal questions, or bringing up issues that she has… opinions on, shall we say.
My mother wasn’t due for any bloodwork, but the doctor did want to see her again in 3 months, so I made that appointment before we headed out.
Since the doctor faxed the new and updated prescriptions directly to the pharmacy in my mother’s town, that was our first stop. I went in while my mother stayed in the car, as it was just too much for her to go in and out. My mother was due to have her bubble packs delivered on Friday, and has started her last week’s current pack, so when I got there, her new packs were already there and ready to go. So that got pulled and adjusted for the new dosage. Instead of delivering on Friday, they will deliver tomorrow. As for the last pack my mother just started, the pharmacist said for her to set it aside and use the new once when they arrive, and the current pack can be brought back and adjusted.
As for the inhaler, it would take an hour before it would be ready, so that will be delivered tomorrow, too. Having been given an inhaler to see if it would help with my own respiratory issues (which we’ve never found the cause of, and I’ve basically given up trying to find one), I was able to explain to my mother how they work and how to use one, etc. She’ll need reminding, of course, but I hope the staff that delivers her meds tomorrow will be able to explain it again.
That done, there was just a brief stop at the grocery store for me to run in and pick up a couple of things for my mother before I took her home. I didn’t stay too much longer after that. I’m glad the days are longer, and I did manage to get home while it was still light out.
In between all this, I was able to send the OBDII scan results on the truck to the garage and he was able to respond. It’s basically the oil pressure sensor again. The one that was recently replaced, and also recently cleaned out because it was triggering the alarm and “shut off engine now” warnings, because it thought the truck was out of oil. This time, it has so far just turned on the check engine light again (though I did clear the codes, so that should be off now), and it why the oil pressure gauge isn’t moving. He told me, even if he replaced the sensor again, it’ll keep happening, because of the weather we’ve been having. There’s really nothing he can do about it. I suppose I could pay him to take it apart and clean it again, but that’s about it.
So really, what I need to be doing is getting the engine warmed up and staying warm long enough to evaporate any moisture in the system and triggering the sensor. It’ll resolve itself as things warm up again, as there won’t be that build up of moisture anymore.
I don’t need to go anywhere tomorrow, and it’s supposed to be a bit warmer, so I’ll run the engine while I’m outside.
Which leads me to my phone call with my brother this evening.
I’d sent the pictures he took to the company that installed the ejector, and the response was the same. The pump isn’t pushing out the water fast enough to create the pressure needed. This frustrated my brother to know end, because he knows the pump is pushing fine. As for how long it takes to drain the tank, he told me that 5 minutes is about right, because our tank is about twice the size of most other tanks. It’s huge. I was so young when it was installed, I was probably not allowed to go anywhere near it at the time.
Plus, that ice wall on the sheet of metal roof the ejector expels the water onto shows just how far and how strong the flow of water is.
Or was.
I know I’ve described the ejector system before, but my brother sent me some info with a diagram. The image was a pdf and terrible pixelated, but I think I got a decent screen cap of it.
I don’t know if ours is from this company, but it’s the exact same design.
With our new ejector, it’s about 2′ above ground, so about 8′ is below ground. I think the original was more like 12′ based on how much more was above ground than the new one. The venturi pipe – the discharge pipe, in the diagram – should never stay full once the pump shuts off. Once installed, the venturi pipe can be (carefully!) removed and replaced, which is what we were supposed to do after using enough hot water to thaw the ice and free it.
One of the things my brother brought up again was electric heat tape. There are all kinds of heat tape, and my husband had sent me a link for one that he’d found on Amazon. As my brother voiced concerns that, if we did try to use heat tape to thaw the above ground portion of the 4″ stand pipe, it might melt the plastic, I sent him the link. It is safe for both metal and plastic pipes, and self regulating. It’s also available in a huge range of lengths. He estimated that a 12′ length would be enough to wrap around the pipe, up to the elbow coming out of the cap. It was affordable, so I ordered it. It’s estimated to arrive on the 17th, though, so we have other things to try.
One of the things my brother thinks is a contributing factor is the new location of the ejector. The old one was about 10-15 feet away, and had a big willow overhanging it. The willow may have protected it from the elements (even though the roots were probably why it was starting to lean backwards and eventually start leaking). Right now, the ejector may be in full sunlight, but it is completely exposed to the winds we get. With the temperatures we’ve had lately, that could be a contributing factor so a slow freeze happening, and to the slow flow I was seeing in the filter. As long as some water was getting through, it wasn’t freezing completely, though, and just building up. I have a theory. The night before I discovered no flow was happening at all anymore, the septic pump had not gone off at all. Normally, between the 4 of us, plus my older daughter working at night, there’s plenty of toilet flushing, dish washing and even at least one shower. That didn’t happen, and it may have allowed for the stand pipe to finally freeze solid, and the venturi (discharge) pipe along with it.
I had already been thinking that, in the spring, I would need to put some sort of fence around the new ejector. Being so much lower to the ground, the renters cows out traipse right over it, even with the metal sheet butted up against it to divert the flow of water. My brother was thinking we’d need to build some kind of semi-permanent shelter over or around it, to protect it from the element in winter. I say “semi-permanent” as we need to assume that, some day, it will need to have work done on it, and we’d need to be able to move it.
At one point, I thought of the catio. It has a clear roof and is wrapped in plastic, making it almost a mini greenhouse. It would fit over the ejector.
Then I remembered the metal sheet. It couldn’t fit on top of that, since it has a curl to it that ensures the water flows away, and not off the sides.
But, there was possibilities.
So, while we wait for the heat tape to arrive, we need to see if we can find something we can use to build a shelter over it for this winter. My brother thinks a couple of pallets set up as a V around it, then something on top, would do the trick. We have no pallets, but he’s sure he brought some. There might also be some scrap plywood we could find somewhere.
Which means, I have a task for tomorrow. Going through the barn and sheds to see what I can find that could be used to build a shelter over the ejector. Just something we can slap together for now, but strong and heavy enough to not be blown over and destroyed by the wind. Ideally, I’d find something clear for a “roof” and add a little passive solar heat.
Trudging around outside will also give me a chance to get the truck running and see how it does! We’re warming up over the next few days, including the overnight lows, which should help, too. The day after tomorrow, my daughter and I have our joint appointment. It would be good if we could use our own truck and return my brother’s car! They really do need two vehicles.
Well, we’ll see how it goes. There’s not much else we can do!
Meanwhile, our septic tank still hasn’t filled enough to trigger the pump, so we still don’t know if the diverter will actually work, yet. It should work just fine. It’s just that we’ve had so many things breaking down for so long, now, I’m getting pretty paranoid about it all!
*sigh*
Ah, well. We’ll manage.
What other choice do we have?
The Re-Farmer
The Re-Farmer 