Normally, I would have gone into the city today for our first stock up shop. I’d forgotten what day it was when I arranged for someone from the hospital the TCU my mother is in to call me.
No one called.
*sigh*
I headed out to work on the chicken coop in the early afternoon. I had decided last night on how I would modify the coop to include roosts in front of the nesting boxes, if I could find the materials for it.
I did.
After taking some measurements (it was very awkward to reach where I needed to measure!), I dug around the scrap but useable lumber bits in the garage my brother gave me and found a 2×4 that was long enough. I cut it to the length I needed for the roosts with my miter saw, but was stuck trying to figure out how to cut it in half length wise. A hand saw would just take too long, and the old table saw we have stored in the sun room would have been too much of a pain to get out and use for just one cut. In the end, I got my jig saw out of winter storage and used that.
The down side is that I got a wonky cut out of it. When it came near the end, I flipped the board and restarted at the uncut end. Of course, it went wonky and I ended up with a jaggy bit where the cuts met. I ended up taking the pieces to the vice in the other side of the garage and smoothed the roughest parts with my draw knife. Then they got a sanding, just with some course sand paper, so the pieces were smooth on all sides, and the edges were slightly rounded. Should be much nicer on chicken feet!
While getting the jigsaw out of storage in the basement, I looked through the scrap we had there and found a leftover piece of wood that was the right width to use as uprights to support the roosts. I measured off and cut two 12″ pieces, then took everything to the coop to see how they fit. I found I needed to trim a bit on the cross pieces, then remembered that I needed two more upright supports. The remaining piece of wood was just shy of 2′ long, so I ended up cutting it in half and getting two pieces just barely over 11 inches long.
I also had a package of right angle brackets and used those to attach the uprights to the cross piece, though I did have to trim just a touch off the cross pieces for them to fit. Unfortunately, the angle brackets I had are dollar store cheepies, and the screws just did not want to bite! It almost took longer to screw on the angle brackets than it did to cut the wood to size!
I got them done, though, and have set them up inside the coop, in front of the nesting boxes.
I had to use a little household step ladder to be able to reach in and set one end in place, from above. Ideally, these should have been installed when before the end walls were attached, but I hadn’t figured out how to add the roosts inside, yet.
You can see the new roosts in the second and third photos of the slideshow above. At this point, I had to stop. The uprights need to be secured to the walls. Otherwise, they’ll just fall loose while the coop is being worked on and moved around. I’ll have to screw them in place from the outside.
After going through my collection of screws, I realized I didn’t have anything the right size. I will be going into the city tomorrow for the stock up trip I normally would have done today, and one of my stops is Canadian Tire for litter pellets, so I can pick up the right screws while I am there.
Which means there will be no progress at all on the coop tomorrow, nor probably the day after, as that is when I would be going into the city again for the Costco shopping. My daughter will probably be coming with me, so she won’t be working on it for me, either.
Thankfully, we don’t actually need it for quite some time, and by the time we can get back at it, the weather should be warming up again.
As I was putting everything away, I spotted these adorable ones.
They really love that pile of straw mulch I’d moved under the mock orange bush!
When doing the evening cat feed, I saw Slick. She didn’t show up this morning, so I was glad to see her. As I put food on the cat house roof, her favourite place to eat, she actually came over, purring, and wanting pets! Which I stopped to do, and made a point of trying to feel under her belly. I was hoping to feel and active nips she had, to get an idea of how many kittens she has.
I felt none at all.
Which is very strange. I’m sure I would have felt something if she were nursing kittens. Either she just has one and the active nip was somewhere I wasn’t able to touch her, or … did she lose her litter? It’s really hard to know at this point. After she ate, she suddenly got strange on me again and moved away as I came close, even if it was to pet a different cat. As she moved around, I tried to see her belly fur, and still, nothing.
I don’t know what to make of it.
As I continued my evening rounds, I checked on the fruit and berry bushes. It’s too early to see if they all survived the winter at this stage. One exception is the silver buffaloberry.
The branches are absolutely covered with these tiny little leaf buds!
I may have made a mistake in not covering the trellis bed, with the peas and carrots. Peas are cold tolerant, but newly uncovered sprouts may not have been strong enough to handle the overnight temperatures we’re having right now. Some of the other beds, the rows got re-covered in leaves by the wind, which I’ve left, as it may be protecting any seedlings from the overnight cold. It’s too early to tell, even with the beds that are under plastic.
The colder temperatures are good for the poppy seeds I sowed, though. This is nature doing the cold stratification for me.
Hopefully, the winter sown beds will make it. If not, I’ll have a lot of free space to plant into, when things finally warm up!
I might just pick up more packages of certain new seed varieties I was trying, just in case…
😁
The Re-Farmer
The Re-Farmer 