While the temperatures today are cooler than yesterday, the rain has stopped and the sun has come out, so I was very happy to finally get outside!

While there is a lot to do all over, I am wanting to prioritize getting things winterized for the cats as much as possible. Today, that meant working on the isolation shelter.

Yes, I moved it by the house.

Yes, I moved it by myself.

Very slowly. Very carefully. Even with the rain, the ground was not too soft, and none of the wheel sank too much. Once I got to the sidewalk and could keep at least 2 wheels on the concrete blocks, it went a lot faster and smoother.

I had been working on it for a while when my daughter came out, having remembered we needed to pick up a package at the post office. We headed out together and it’s a good thing she interrupted me. After sitting in the truck for a while, my body started letting me know that I really needed to stop for the day, before I pushed things too far. So when we got back, I went over what I’d done so far with her, and what I was working on when I stopped, so she could take over for me, if she got to it before I did.

After cleaning up and putting things away, I decided to take a short video, instead of photos.

Before moving it, I took out the sliding windows, emptied it and cleaned out the bottom as best I could. The litter box had been tipped on its side, long enough ago that all the sawdust from the litter pellets was dry. I have a car bush/squeegee/scraper combo with a telescoping handle and a brush the rotates 90° that works really well for that. The scraper end broke long ago, but the brush/squeegee end has been so very handy when it comes to cleaning the and isolation shelter and the catio roof. I was able to brush most of the sawdust through the mesh floor. If it were spring or summer, I would have hosed it down, too, but I wasn’t going to do that this time of year.

When my older daughter and I removed the plastic (vinyl dining table covers, actually) from around the bottom earlier in the year, I made sure to label all the wood lath pieces with where they came from, and kept their screws in the wood, so I could put them back in the same places without making new holes in the wood frame. The vinyl is two pieces that overlap at the back. Their bottoms were pretty damaged from last winter. One of them was a lot more damaged at one end at the back than the other. While against the house last winter, there was enough space behind it that the cats can fit on top of some things I had stored behind it, and they sometimes slipped, clawing the plastic in the process. With that one, I folded the most damaged part in on itself. The vinyl table protectors are folded in half already, so the overlapping part in the back now has 6 layers in the middle, instead of four.

While we tried to store the vinyl as smoothly as possible, it was still pretty wrinkled, which made securing it with the wood a bit more challenging. On one end, the bottom was torn up enough that I had to use my clear repair tape before I could secure it with the wood lath.

I’d also had a length of wood lath at the back of the roof, joining the roof supports. It had been nailed in place and kept popping off, so I finally tucked it under the roof panels. Today, I put it back with tiny screws, instead of nails. This is to keep the roof supports from wobbling unevenly when it’s lifted. It’s not an issue at the front, where the hinge is. Two more supports were added under the roof panel to stop some sagging. I’ll need to bring the little step ladder out, and then I’ll add some more screws to secure the panels directly to the added supports in the middle, where I can’t otherwise reach.

One of the things I made sure to do was put rigid insulation on the walls of the upper level. The piece that was in the side over the hammock, however, was rather loose and kept falling down into the hammock, or even down to the lover level, before finally breaking. Cats in the hammock would use it as a scratching post, too, and kept pulling it loose. That panel is nothing but wood lath, with some pieces bowing a bit. Wind can get through it quite easily, so I wanted to put new insulation in there. This time, I used my measuring tape calipers to figure out the dimensions properly. When I’d added the insulation before, the front window hadn’t been put on yet, so it was easy to access. I basically just held the insulation to the space and cut it mostly by eye. Which would have worked fine, if there was no wind or cats to make it fall out. I had just finished cutting the piece to fit around the corner brace and the small piece of wood that’s screwed into the inside corner at the top. I had tried to fit in in place, and it is just the tiniest bit too wide. I could force it in place and it would hold very well, but I want to cut a second, matching piece, first, to make a double layer of insulation. The inside one, right up against the wood, can be trimmed to fit without being forced, and I am thinking the outside one can be left without trimming, and be tight enough to not be pulled out by the cats too easily – and if they do, there will be a second layer beneath it.

Not today, though. I’m glad my daughter came out when she did and distracted me. Otherwise, I would have kept going for quite a while and potentially injured myself before realizing it.

Speaking of injuries, once I’ve had my follow up appointment, and our doctor is at her new location, I need to get that left shoulder checked. It is starting to be a problem. The arm is strong, but range of motion is increasingly limited.

All in good time.

I’m just really happy with how much I was able to do today, while the weather is so lovely right now!

The Re-Farmer